Rockwell-automation 5730 DriveLogix5730 Controller for PowerFlex 700S Manuel d'utilisateur Page 195
- Page / 217
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
DriveLogix5730 Controller Specifications A-7
Network Status (NS) indicator
Link Status (LNK) indicator
solid red held in reset The controller is holding the port in reset or the
controller is faulted.
Clear the controller fault.
Replace the controller.
self-test The port is performing its power-up self-test. Normal operation during power-up. No action
required.
major fault An unrecoverable fault has occurred. Cycle power to the controller.
Replace the controller.
flashing red updating firmware The port firmware is being updated. Normal operation during firmware update. No
action required.
Condition: Status: Indicates: Recommended Action:
Condition: Status: Indicates: Recommended Action:
off not initialized The port does not have an IP address and is
operating in BOOTP mode.
Verify that the BOOTP server is running.
flashing green no CIP
connections
established
The port has an IP address, but no CIP connections
are established.
Normal operation if no connections are
configured. No action required.
If connections are configured, check connection
originator for connection error code.
solid green CIP connections
established
The port has an IP address and CIP connections
(Class 1 or Class 3) are established.
Normal operation. No action required.
solid red duplicate IP
address
The port has detected that the assigned IP address is
already in use.
Verify that all IP addresses are unique.
flashing red/green self-test The port is performing its power-up self-test. Normal operation during powerup.
Condition: Status: Indicates: Recommended Action:
off no link The port is not connected to a powered Ethernet
device.
The port cannot communicate on Ethernet.
Verify that all Ethernet cables are connected.
Verify that Ethernet switch is powered.
flashing green self-test The port is performing its power-up self-test. Normal operation during powerup.
data transmission
and reception
The port is communicating on Ethernet. Normal operation.
No action required.
solid green link OK The port is connected to a powered Ethernet device.
The port can communicate on Ethernet.
Normal operation.
No action required.
- DriveLogix™ 5730 1
- Controller 1
- Important User Information 2
- Summary of Changes 3
- Table of Contents 5
- Configuring DriveLogix Motion 6
- Appendix B Access Procedures 7
- Overview 9
- Related Documentation 10
- Contacting Tech Support 10
- Controller Firmware 11
- Revision 11
- General Precautions 11
- What is DriveLogix5730? 13
- Loading Controller 14
- Firmware 14
- What is DriveLogix5730? 1-3 15
- 1-4 What is DriveLogix5730? 16
- Using CompactFlash 17
- 40012.eps 18
- What is DriveLogix5730? 1-7 19
- 030252015105 454035 50 656055 20
- Overhead Percentage 21
- Selecting a System 21
- Understanding the Virtual 24
- Backplane 24
- Chapter 2 25
- Determining When the 26
- Controller Updates the Drive 26
- Placing and Configuring the 27
- Electronic Keying 28
- Communication Formats 29
- “drive_module” 30
- Inhibiting the Drive 35
- Connection 35
- Using DriveExecutive Lite 36
- 3. Select the Power tab 37
- 6. Select the Setup tab 38
- Mode Change 41
- 5. Click the Apply button 44
- Accessing Drive Data 45
- Monitoring Drive Data 45
- Configuring the Controller’s 46
- Response to a Connection 46
- Monitoring the drive module 47
- Recommended 49
- Programming Techniques 49
- Chapter 3 51
- 20D-DL2-CL3 52
- 20D-DL2-CR3 52
- Validating I/O Layout 53
- Estimating RPI 54
- Controller Updates I/O 54
- Configuring the 55
- CompactBus 55
- Configuring Local I/O 57
- GSV ladder.tif 61
- Accessing I/O Data 62
- Example: 63
- Direct Connections for I/O 64
- Monitoring I/O Modules 65
- 27 19 11 66
- Configuring I/O Modules 67
- Using the Generic 67
- 1769-MODULE 67
- Programming the Controller 72
- Forward 83
- Reverse 83
- Launching DriveExecutive 84
- Then click Apply 85
- Configuring the Drive with 86
- DriveExecutive Software 86
- Downloading the Settings 90
- Additional Testing and 90
- Programming is Necessary 90
- Supported Motion 91
- Commands 91
- Chapter 5 93
- Configuring the Hardware 94
- Example 1: Workstation 98
- Directly Connected to a 98
- DriveLogix Controller 98
- Example 2: Workstation 99
- Remotely Connected to a 99
- Example 3: DriveLogix 102
- Controller to a Bar Code 102
- Configuring User Mode 104
- Chapter 6 105
- EtherNet/IP 106
- Controller Connections 115
- Over EtherNet/IP 115
- Configuring Distributed I/O 116
- Accessing Distributed I/O 117
- Adding a Remote Controller 119
- Producing and Consuming 119
- Producing a tag 121
- Consuming a Tag 122
- Sending Messages 123
- Mapping Addresses 126
- Using a MSG Instruction to 128
- Send an Email 128
- Creating String Tags 129
- Entering String Data 129
- Entering Ladder Logic 130
- Example 1: DriveLogix5730 135
- Controller and 135
- Distributed I/O 135
- Example 2: Controller to 136
- Sending a MSG instruction 138
- Receiving a MSG Instruction 139
- Chapter 7 141
- Configuration folder 143
- Scheduling the ControlNet 147
- If you have this software 150
- Then you can cache: 150
- Producing a Tag 156
- Guidelines for Configuring 157
- Connections 157
- Example 1: DriveLogix 158
- Controller and Remote I/O 158
- Example 2: DriveLogix5730 159
- Controller to 159
- DriveLogix5730 Controller 159
- Controller to Other Devices 162
- Chapter 8 167
- Example: Controlling I/O 168
- Over DeviceNet 168
- Module Command Array 174
- CompactBus: 176
- Entering Program Logic 178
- Chapter 9 179
- Configuring Your System for 180
- Planning a DH-485 Network 182
- Network Initialization 183
- Installing a DH-485 Network 184
- Browsing a DH-485 Network 187
- Remotely 187
- Appendix A 189
- DriveLogix5730 190
- Certifications 190
- Real-Time Clock Accuracy 190
- Controller LEDs 191
- CompactFlash card LED 193
- Embedded EtherNet/IP 194
- Option LEDs 194
- Network Status (NS) indicator 195
- Link Status (LNK) indicator 195
- Battery Life 196
- Appendix B 197
- Removing the Outside 199
- Removing the Inside Cover 199
- Connecting the Battery 200
- Replacing the Battery 201
- Installing the Embedded 203
- EtherNet/IP Option Board 203
- Installing the 203
- DriveLogix5730 Expansion 203
- Installing the Compact I/O 204
- Communications 205
- Daughtercard 205
- B-10 Access Procedures 206
- Application Restrictions 207
- Hold Last State and 209
- User-Defined Safe State Not 209
- Supported 209
- C-4 Application Restrictions 210
- Numerics 211
- Allen-Bradley 217
Produits connexes et manuels pour Équipement Rockwell-automation 5730 DriveLogix5730 Controller for PowerFlex 700S
Équipement Rockwell-automation 42KA Subminiature Flat Pack PHOTOSWITCH Manuel d'utilisateur
(4 pages)
(4 pages)
Équipement Rockwell-automation 22-COMM-P PowerFlex Profibus Adapter Manuel d'utilisateur
(116 pages)
(116 pages)
Équipement Rockwell-automation 20M LPM15 Liquid-Cooled Adjustable Frequency AC Dr Manuel d'utilisateur
(148 pages)
(148 pages)
Équipement Rockwell-automation 140G-K-PB3L_PB4L_PB3H_PB4H Phase Barriers Manuel d'utilisateur
(2 pages)
(2 pages)
Équipement Rockwell-automation 42EF LaserSight RightSight Photoelectric Sensors Manuel d'utilisateur
(4 pages)
(4 pages)
Équipement Rockwell-automation 100 Contactors with 3-terminal DC Coil Manuel d'utilisateur
(1 pages)
(1 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels