Rockwell-automation IASIMP Computer Numerical Control (CNC) Machining Manuel d'utilisateur Page 137
- Page / 278
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Rockwell Automation Publication IASIMP-QS034A-EN-P - October 2012 137
GuardLogix Configuration Chapter 4
Safety Logic Integration
There are different ways to provide a safety system for a CNC machining work cell. This toolkit provides an
example of a supervisory GuardLogix safety controller that provides safety control for the two gantry drives, an
EStop, a light curtain, and provides safety interlocking with the Dual Check Safety systems of the two CNC
systems.
Safety I/O
The safety interface between the GuardLogix controller and FANUC CNC Dual Check Safety systems is
accomplished through the safety I/O of both systems. For safety category 3 and 4, two output channels and two
input channels of GuardLogix I/O are connected to two input channels and two output channels of the Dual
Check Safety I/O, as illustrated in Figure 18.
Figure 18 - Safety I/O Example
This wiring interface is included in the system layout and wiring library within this toolkit. Refer to the Dual
Check I/O and 1791 Guard I/O drawings.
00
01
00
01
00
01
00
01
GuardLogix
Safety Outputs
Dual Check
Safety Inputs
GuardLogix
Safety Inputs
Dual Check
Safety Outputs
- Accelerator Toolkit 1
- Important User Information 2
- Chapter 7 3
- Where to Start 4
- Chapter 4 6
- GuardLogix Configuration 6
- Chapter 5 6
- Appendix D 9
- Configuration 9
- Table of Contents 10
- Introduction 11
- Conventions 12
- Required Software 12
- Additional Resources 13
- FANUC CNC Express Software 19
- System Layout and Wiring 29
- • The 07_PLC_1791DS_IB16 and 32
- Project Drawings folder 33
- Edit FANUC CNC Drawing Set 34
- Edit CNC Power Drawings 35
- • 16_CNC_Ethernet_Switch 41
- • 18_CNC_Cable_Connections 41
- CNC Subpanel Layout Drawing 43
- CNC Enclosure Layout Drawing 43
- Drive Power Example 44
- Drive I/O Example 44
- System Layout Example 44
- FANUC CNC Configuration 47
- Parameter Write Enable 49
- High Speed Ethernet Option 51
- Configure Ethernet Module 53
- Create a New Project File 56
- 5. Select the model 58
- USB External Device 63
- EtherNet/IP Settings 64
- Logic Configuration 68
- P0001 (OP Panel Path 1) 71
- P0005 (Machine Sequence) 71
- P0010 (Window Functions) 72
- P0023 (Alarm Routine) 72
- Device Logic Modules 73
- 4. Click to save your FANUC 76
- LADDER III application file 76
- Figure 8 - Logic Modules 81
- Order and Run the DMAT Wizard 84
- Save the Project File 90
- 9. Click OK 94
- FANUC CNC AOP Configuration 95
- Add and Configure FANUC CNC 96
- The Import Configuration 101
- Import 105
- Machining Example 109
- Drill CNC Example 109
- Gantry Y Axis Drive Example 110
- Machine CNC Example 110
- Gantry X Axis Drive Example 110
- • Drill CNC 111
- • Machining CNC 111
- • Gantry X Axis Drive 111
- • Gantry Y Axis Drive 111
- IMPORTANT 113
- _ModuleNameXX tag 116
- Logic Placeholder 121
- Safety Logic Integration 137
- GuardLogix Safety Logic 138
- Safety Faceplate Logic 144
- Before You Begin 149
- What You Need 149
- Follow These Steps 150
- Delete Unused Displays 154
- Delete Unused Parameter Files 155
- Configure Parameter Files 156
- Parameters 157
- Comments 157
- Chapter 6 158
- • SafeIOAlarmTrigger 160
- • ModuleAlarmTrigger 160
- • CNCAlarmTrigger 160
- • CIPMotionAlarmTrigger 160
- Add Parameter Files 165
- Parameters folder 166
- Import Alarm Setup File 171
- • SaveIOAlarmTrigger 173
- Import and Edit Alarm Tags 174
- Goto Display Buttons 189
- CellGuard1 193
- System Commissioning 195
- Download Applications 197
- Terminal 202
- Commissioning Devices 205
- Verify Network Communication 206
- 1756-EN2TR 207
- EtherNet/IP 207
- • If there is an active 211
- Clearing Faults 212
- Operator (manual) Control 212
- Program (automatic) Control 213
- System Application Guide 215
- Machine Startup Faceplate 217
- Machine Control 219
- Program/Operator Mode 219
- CNC Faceplate 221
- CNC Status Views 222
- CNC Control Views 222
- Fault Indication View 223
- Fault Diagnostic Views 224
- Configuration View 225
- Guard I/O Safety Faceplates 226
- Logic Program Overview 229
- Module Routine Overview 231
- Machine Module 234
- Machine Control Module Tags 236
- Application Modules 240
- Device Modules 241
- Logic Module Customization 243
- • Mode = UDT_MachMode 244
- • Command = UDT_MachCmd 244
- • State = UDT_MachState 244
- (2) Refer to Chapter 5 246
- Module Fault Customization 249
- Appendix 255
- Add Optional Faceplate Views 258
- Verify Your IP Address 262
- Load the Controller Firmware 265
- Assign IP Addresses 267
- Numerics 271
- Rockwell Automation Support 278
- Documentation Feedback 278
Produits connexes et manuels pour Équipement Rockwell-automation IASIMP Computer Numerical Control (CNC) Machining
(4 pages)
Équipement Rockwell-automation SP120 ACDrive 115VAC, 1Ph, 230VAC, 1Ph/3Ph, 1/4-5. Manuel d'utilisateur
(210 pages)
(210 pages)
Équipement Rockwell-automation MDO16GNS 16-Channel Digital Output Module 48Vdc Manuel d'utilisateur
(16 pages)
(16 pages)
Équipement Rockwell-automation T8451 Trusted Industrial Control System Manuel d'utilisateur
(2 pages)
(2 pages)
Équipement Rockwell-automation T8480 Trusted TMR Analogue Output Module Manuel d'utilisateur
(2 pages)
(2 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels