Rockwell-automation 6000 PowerFlex Medium Voltage Variable Frequency D Manuel d'utilisateur Page 90
- Page / 98
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
90 Rockwell Automation Publication 6000-IN007A-EN-P - October 2014
Appendix C Special Function Parameter Settings
Speed Command Functions
Set Frequency Command Source
Relevant parameter: P262
Description: this function selects the frequency command source (analog or
digital).
Instruction: If P262=0, digital setting is selected, if P212=1, analog setting is
selected. Digital mode is setting the frequency from HMI, analog mode is setting
the frequency from hard-wired analog I/O. These two modes cannot be enabled
at the same time.
Set Frequency Correction
Relevant parameters: P259, P260
Description: this improves the sampling accuracy.
Instruction: Set Frequency=P260*Original Set Frequency+P259.
Frequency Command Deadband Upper Limit
Relevant parameter: P414
Description: this function limits the low frequency starting range, reduce the low
frequency output error for analog input mode. This parameter avoids the drive’s
output fluctuation when the frequency is around 0 Hz.
Instruction: if the original set frequency is lower than P414, the set frequency will
be changed to P414.
IMPORTANT
It can only be enabled when the setting frequency source is set to analog.
- Commissioning Manual 1
- Important User Information 2
- Table of Contents 3
- Table 1 - Electrical Drawings 7
- General Precautions 9
- Additional Resources 9
- Introduction 11
- Documentation and 12
- Application Review 12
- Review Drive Application 13
- Chapter 1 Introduction 14
- Preparation and Inspection 15
- Inspect Drive Components 16
- Functional Assessment 17
- Interconnection Review 20
- Installation Review 21
- Power Cabling 22
- Drive Megger Check 23
- Figure 4 - Control Switches 25
- Figure 5 - Control Switches 25
- Figure 8 - Back of HMI 26
- Connect the Insulation Meter 27
- Final Steps before 29
- Equipment is Ready for 29
- Energization 29
- Commissioning 31
- Control System Check Setup 32
- Control System Check 35
- , press 36
- Access Setup Settings 37
- Set P Parameters 38
- Commissioning Chapter 3 39
- Chapter 3 Commissioning 40
- Increase Frequency by Step 41
- Simulate Warnings and Faults 45
- Verify E-Stop Functionality 50
- (Manual Bypass) 52
- Bypass Isolation Switches 54
- (Automatic Bypass) 55
- , and press 57
- Bypass Contactors 58
- Figure 17 - Status Indicators 61
- Table 9 - Drive to DCS 61
- Table 10 - 4-20 mA 61
- Restore P Parameter Settings 62
- Set Date and Time Zone 64
- No-load Test 67
- Configure P and T Parameters 68
- 0 ON -100 199.99 R&D 69
- (2) With Remote DCS only 70
- Parameters T11...T13 71
- Chapter 4 No-load Test 72
- Change Parameter T12: 73
- 3. Press to accept 73
- Close Input Circuit Breaker 75
- Check Cooling Fan Operation 75
- Operate Motor by HMI 76
- No-load Test Chapter 4 77
- Press to confirm 78
- Load Test of Drive System 80
- Torque Requirements 81
- Single Line Diagrams 83
- Appendix C 87
- Overview 87
- System Setting Functions 87
- Switch Control Sources 88
- Motor Parameter Setting 88
- Restore Factory Setting 89
- Speed Command Functions 90
- Frequency Amplitude Limit 91
- Frequency Skip 91
- Speed Reference Functions 92
- Analog Input 93
- Stop Mode 93
- Flying Start Function 93
- Restart the Drive 94
- Rockwell Automation Support 98
- Documentation Feedback 98
Produits connexes et manuels pour Équipement Rockwell-automation 6000 PowerFlex Medium Voltage Variable Frequency D
Équipement Rockwell-automation 2708-DH5B2L_DH5B4L Attended Workstation Manuel d'utilisateur
(186 pages)
(186 pages)
Équipement Rockwell-automation 2711PC-xxxx PanelView Plus 6 Compact Terminals Use Manuel d'utilisateur
(162 pages)
(162 pages)
Équipement Rockwell-automation 2364F Regenerative DC Bus Supply Unit (RGU) Manuel d'utilisateur
(222 pages)
(222 pages)
Équipement Rockwell-automation 2755-SNx Adaptascan Bar Code Readers Manuel d'utilisateur
(354 pages)
(354 pages)
Équipement Rockwell-automation 2080 Micro800 Digital and Analog Plug-in Modules Manuel d'utilisateur
(108 pages)
(108 pages)
(52 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels