Rockwell-automation 1336T Function Block Prog. Manual, Series A/B Manuel d'utilisateur Page 139
- Page / 180
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5–23Block Transfer Services
1336 FORCE — 5.9 August 1995
Message Operation for Subsequent Packets
The packet number determines where the packet’s event data is
written in the drive’s event list. The drive uses the information
contained in Word 4 of packet 0 to re–assemble the packets in the
correct order. When Word 4 is not 0, Word 4 contains the packet
number, Word 5 contains the number of valid events within the
packet, and Word 6 contains the checksum for the events in that
packet.
The Task Status service indicates when a download is in progress
and the service is waiting for event packets. If a download is in
progress and there are no errors, the Fault Read service’s code
identifier (word 5) indicates which packets have been received. The
packets do not need to be sent in order.
After the drive receives all packets required for the application, the
drive performs a number of checks on the data. After all the service
checks have passed, the function block compiler is activated and the
service is acknowledged. However, compilation is not complete
when the last packet is acknowledged. Instead, compilation is
performed as a background task.
Compile time errors will soft fault the drive. If no compiler errors
are found, all function blocks are processed. If no errors occur after
this, the function block task is enabled for execution.
Note: If the data fails the tests, the drive will Not AcKnowledge
(NAK) the service but will not fault the drive, and a warning will be
logged in the drive’s warning queue. These service failures reset the
service to accept another download and compile attempt. The
currently active application is not interrupted.
Important: You must disable the drive to perform a Download and
Compile operation. The drive will reject the download
and compile operation if the drive is running.
The download operation should be performed as a one–shot
procedure.
For more information about downloading and compiling, refer to the
following sections:
For Information About Refer to Chapter
Events 2
Examples 2
Compiler Process 2
Compile Modes 3
Task Status 5
Fault Status 5
Download and Compile
(continued)
- Function Block 1
- Programming 1
- Important User Information 2
- Table of Contents 3
- Function Block Library 4
- Chapter 6 5
- End of Table of Contents 6
- Chapter 1 7
- Chapter 2 7
- PrefaceP–2 8
- Preface P–3 9
- Components 10
- End of Preface 12
- Getting Started 13
- Getting Started Using 15
- DriveBlockEditor 15
- ❒ Click on CLOSE 16
- BLOCK ID# 17
- Set Reset FF 18
- 1–7Getting Started 19
- Multiplexer 20
- 1–9Getting Started 21
- Rate Limiter 22
- Step 6 — Check Links 23
- Step 7 — Download the Program 23
- Block Nodes 24
- 1–13Getting Started 25
- Step 9 — Modify Node Values 26
- Getting Started Using a PLC 27
- 1–16 Getting Started 28
- Step 3 — Write Node Values 29
- 1–18 Getting Started 30
- Step 4 — Write Links 31
- 1–20 Getting Started 32
- Step 5 — View Node Values 33
- Download to Drive 33
- 1–22 Getting Started 34
- System Component Detail 35
- 2–2 System Component Detail 36
- 2–3System Component Detail 37
- 2–4 System Component Detail 38
- Example Execution Lists 39
- Linking Events 39
- ADD2 SCALEInput Output 40
- MULTIPLY 40
- Downloading and 42
- Compiling the Execution 42
- Understanding Function 43
- Block I/O Nodes 43
- Node Data Types 46
- Creating Links Between Nodes 47
- 2–14 System Component Detail 48
- System Interactions 49
- The Function Block Init 50
- The Function Block Store 50
- The Function Block Recall 51
- Linear Parameter 51
- BRAM Functions and Links 51
- Power Up Sequence 53
- Compiler Modes and Terminal 54
- Operation Differences 54
- Compiler Modes 54
- Subsequent Compile Mode 55
- DriveTools’ DriveBlockEditor 56
- Operation 56
- Graphic Programming 57
- Terminal 57
- PLC Block Transfer 57
- Understanding Multiple 58
- Execution List Copies 58
- Task Status Service 59
- Link Processing Faults 60
- Performance Issues Involving 61
- Link Processing Sequence 62
- Double Word Function Block 64
- Function Block Index 65
- BLOCK TYPE 1 66
- BLOCK TYPE 3 67
- 0 000001000000010 68
- COMPHYST 69
- BLOCK TYPE 5 71
- 0 000000000001110 72
- BLOCK TYPE 6 73
- BLOCK TYPE 7 75
- BLOCK TYPE 23 77
- BLOCK TYPE 25 80
- BLOCK TYPE 8 81
- BLOCK TYPE 2 83
- BLOCK TYPE 16 84
- FUNCTION 85
- INTEGRATOR 88
- BLOCK TYPE 12 92
- BLOCK TYPE 15 93
- BLOCK TYPE 13 94
- MONOSTABLE 95
- MULTIPLEXER 96
- DEFINITION 99
- A PLC place holder 99
- BLOCK TYPE 17 100
- (continued) 101
- PULSE CNTR 104
- RATE LIMITER 106
- Example 1 107
- BLOCK TYPE 20 108
- BLOCK TYPE 22 110
- BLOCK TYPE 27 111
- BLOCK TYPE 11 112
- BLOCK TYPE 26 113
- UP/DWN CNTR 114
- Block Transfer Services 117
- Block Transfer Status 118
- Application Status 120
- Services: 120
- Event List Checksum 121
- 3842 –– Message OK 124
- –28926 –– Message Error 124
- 3841 –– Message OK 125
- –28927 –– Message Error 125
- Read Task Status 127
- 3845 –– Message OK 128
- –28923 –– Message Error 128
- Fault Status Read 129
- 3840 –– Message OK 130
- –28928 –– Message Error 130
- Program Limits 132
- Information: 132
- Application Control 135
- Commands: 135
- BRAM Functions 136
- 0F03 –– Message OK 137
- 8F03 –– Message Error 137
- Download and Compile 139
- Read Single Event 143
- Clear/Process Links 145
- 3844 –– Message OK 146
- –28924 –– Message Error 146
- 0F05 ––Message OK 147
- 8F05 –– Message Error 147
- ID = block ID number 147
- Read Block Value 148
- 0F05 –– Message OK 149
- ID = the block ID number 149
- Write Block Value 150
- 0F06 –– Message OK 151
- 8F06 –– Message Error 151
- Write Block Link 153
- Node Adjustment: 154
- Read Full Node 155
- Information 155
- Read Node Link 160
- Write Node Link 162
- Warnings 163
- Function Block Warnings 164
- ❒ the system fault queue 164
- ❒ the system warning queue 164
- Accessing the System 165
- Fault and Warning Queues 165
- Handling Download 165
- Service Errors 165
- Handling Compile Faults 166
- Link Processing Fault 167
- I/O Node Limit Fault 167
- Memory Limit Fault 167
- BRAM Checksum Fault 168
- Using the Task Status Service 169
- Using the Fault Status 170
- Clear Faults Command 171
- Fault Codes 172
- CUT ALONG DOTTED LINE 177
- ALLEN-BRADLEY 178
- Worldwide representation 180
Produits connexes et manuels pour Équipement Rockwell-automation 1336T Function Block Prog. Manual, Series A/B
Équipement Rockwell-automation 931S-A1A1N-IP1 Passive Isolator, 1 Channel Manuel d'utilisateur
(43 pages)
(43 pages)
Équipement Rockwell-automation 1398-PDM-xxx IQ Master Version 3.2.4 for IA-2000 a Manuel d'utilisateur
(464 pages)
(464 pages)
Équipement Rockwell-automation 1336F PLUS II Custom Firmware Inst. - EN935 Manuel d'utilisateur
(1 pages)
(1 pages)
Équipement Rockwell-automation 1404-M4_M5_M6_M8 Powermonitor 3000 User Manual, PR Manuel d'utilisateur
(356 pages)
(356 pages)
Équipement Rockwell-automation 1326 Digital AC Multi-Axis Motion Control System U Manuel d'utilisateur
(301 pages)
(301 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels