Rockwell-automation 1770, D17706.5.16 Ref Mnl DF1 Protocol Command Manuel d'utilisateur Page 133
- Page / 251
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
8–6 Message Packet Status Codes (STS, EXT STS)
Publication
17706.5.16 - October 1996
Remote STS and EXT STS Codes from a PLC3 Processor
A PLC-3 interface module (1775-KA,-S5,-SR5) inserts the reply
error code in the STS byte of any reply message packet it returns to a
remote node (your computer).
The meaning of each error code depends on the command message
received from the computer. The following pages describe the error
conditions that the various commands can generate. The error codes
are listed according to the decimal value that is stored at the
computer.
When a remote node transmits one of these commands, the local
PLC-3 interface module may issue a reply message that contains one
of the error codes listed under that command. Error codes contained
in the EXT STS bytes are only available if either another PLC-3 or
computer originates the command message.
Command EXT STS Code STS Code Explanation
diagnostic read
- 10
•A twobyte ADDR field and a onebyte SIZE field
are missing after the FNC byte in the command
message.
•The number of bytes of data requested in the SIZE
field is greater than the maximum number allowed
per reply packet (244), or SIZE is 0.
- 50 The command is an illegal request to read from the
PLC3 interface module's backplane window.
diagnostic status - 40 A backplane error occurred during determination of
the physical address of the end of the ladder
diagram program or of the end of user memory.
PLC/PLC2 word write
- 10
•A twobyte ADDR field is expected after the TNS
word, but only one byte is present.
•There is an odd number of data bytes in the
command packet.
•The ADDR value is odd (that is, it does not specify
a word address).
- 30 The local PLC3 interface module has executed a
shutdown request to the local PLC3 processor.
- 40 Local PLC3 backplane error (either memory parity,
timeout, or disconnect).
- 50
•The destination file does not exist in PLC3
memory.
•The destination word does not exist in the
destination PLC3 file.
•The length of the destination file is greater than
65,535 words.
- 60 Local keyswitch setting prohibits writing into desired
destination file.
- 70 The local PLC3 processor is in Program mode.
There may be a major system fault.
- Reference 1
- Important User 2
- Information 2
- What's Changed in This 3
- Document 3
- Table of Contents 4
- Table of Contentsii 5
- Table of Contents iii 6
- Table of Contentsiv 7
- Table of Contents v 8
- Table of Contentsvi 9
- Encoding 10
- Table of Contentsviii 11
- About This Manual 12
- What This Manual 13
- Contains 13
- Terms and Abbreviations 14
- Related Publications 14
- Related Products 15
- Conventions Used in This 16
- Network Basics 17
- Network Layers 18
- Physical Layer 19
- 1–4 Network Layers 21
- 1–6 Network Layers 23
- Software Layers 24
- Message Packet Structure 26
- Protocol 29
- Understanding DF1 Protocol 30
- DF1 Protocol 31
- • request-to-send (RTS) 32
- • clear-to-send (CTS) 32
- • data-carrier-detect (DCD) 32
- • data-set-ready (DSR) 32
- • data-terminal-ready (DTR) 32
- Fullduplex Protocol 33
- Character Transmission 34
- Transmission Symbols 35
- See APP DATA 36
- Send and Receive Messages 38
- Halfduplex Protocol Message 39
- Transmission 39
- Transmitter and Receiver 40
- Message Transfer 40
- Halfduplex Protocol 40
- Environment 40
- 0HVVDJH &KDUDFWHULVWLFV 44
- 0DVWHU 3ROOLQJ 44
- 5HVSRQVLELOLWLHV 44
- )XOO 6LQNV 45
- 6LPSOLILHG 1HWZRUN /D\HU 45
- 6ODYH 7UDQVFHLYHU $FWLRQV 46
- +DOI'XSOH[ 3URWRFRO 48
- 'LDJUDPV 48
- 3ROO ZLWK 0HVVDJH 5HWXUQHG 51
- 0HVVDJH 6LQN )XOO &DVH 53
- 0HVVDJH 6LQN )XOO &DVH 54
- Using Fullduplex Protocol to 55
- Message Transmission 56
- Message Characteristics 58
- Transfer 58
- How the Transmitter Operates 59
- Diagrams 64
- Message Transfer with NAK 65
- In this transfer: 69
- Message Packets 72
- Datalink Layer Message 73
- Message Frames 74
- BCC and CRC Fields 76
- Full-duplex protocol example 77
- CRC Field 78
- Application Layer Message 80
- How Your Application 81
- Program Sends and 81
- Receives Messages 81
- Message Packet Format 82
- DST and SRC 83
- CMD and FNC 84
- STS and EXT STS 85
- Communication Commands 88
- 7–2 Communication Commands 89
- 7–3Communication Commands 90
- 7–4 Communication Commands 91
- 7–5Communication Commands 92
- 7–6 Communication Commands 93
- 7–7Communication Commands 94
- 7–8 Communication Commands 95
- 7–10 Communication Commands 97
- 7–12 Communication Commands 99
- phys. address 100
- 7–14 Communication Commands 101
- SET RESET 102
- to 60 masks of this form 102
- 7–19Communication Commands 106
- 7–20 Communication Commands 107
- 7–21Communication Commands 108
- 7–22 Communication Commands 109
- 7–23Communication Commands 110
- 7–25Communication Commands 112
- 7–27Communication Commands 114
- PLC5 sys. address 115
- Publication 116
- 17706.5.16 - October 1996 116
- Set Reset 117
- 7–31Communication Commands 118
- 7–32 Communication Commands 119
- PLC sys. address 121
- PLC5 Type/Data 123
- Parameter Examples 123
- 7–37Communication Commands 124
- Example: 126
- 7–40 Communication Commands 127
- Message Packet Status Codes 128
- (STS, EXT STS) 128
- STS Byte 129
- EXT STS Byte 130
- Remote STS and 132
- EXT STS Codes 132
- Module Diagnostics 138
- Diagnostic Counters 139
- 9–2 Diagnostic Counters 140
- 1747 Cat. Nos 141
- DH485 Diagnostic Counters 143
- DF1 Diagnostic Counters 144
- 1761 Cat. Nos 145
- 1770 Cat. Nos 146
- Counters 149
- 1771 Cat. Nos 152
- 1775 Cat. Nos 159
- 1779 Cat. Nos 162
- 1784 Cat. Nos 163
- 1785 Cat. Nos 164
- • half-duplex slave 169
- • half-duplex master 169
- 5250 Cat. Nos 171
- Diagnostic Status Information 172
- SLC 5/02 processors only 174
- 1761, 1770, and 1771 176
- Cat. Nos 176
- 1770KF3 Status Bytes 178
- 1773, 1775, and 1779 182
- 1779KP5 Status Bytes 185
- 1785KA5 Status Bytes 188
- 1785KA3 Status Bytes 188
- 1785KE Status Bytes 190
- L60L Status Bytes 193
- 5130 Cat. Nos 194
- Data Encoding 197
- Numbering Systems 198
- Binary Coded Decimal 199
- Hexadecimal 200
- Binary Floatingpoint 201
- Order of Transmission 202
- A 16-Bit Word in PLC Memory 203
- Right-to-Left Bit Order 203
- Uploading and Downloading 204
- Uploading from the 205
- Processor 205
- Downloading to the 209
- PLC Addressing 216
- PLC2/1774PLC 217
- Addressing 217
- PLC2 Physical Addressing 218
- 1774PLC Physical Addressing 218
- PLC3 Addressing 219
- PLC3 Logical Addressing 220
- PLC3 Physical Addressing 222
- PLC3 Symbolic Addressing 223
- • and so on 223
- PLC5 Addressing 224
- PLC5 Logical Addressing 225
- 13–12 PLC Addressing 227
- 13–14 PLC Addressing 229
- PLC5 Physical Addressing 231
- PLC5 Floating Point 232
- • low word then high word 232
- • low byte then high byte 232
- Line Monitor Examples 233
- Halfduplex Line Monitor 234
- Fullduplex PLC2 Line 235
- Monitor Example 235
- Fullduplex PLC3 Line 238
- 14 decimal) 239
- TOTAL TRANS 239
- DLE ETX (2 240
- ASCII Codes 241
- 17706.5.16 July 1996 242
- AllenBradley 249
- Publication Problem Report 249
- BUSINESS REPLY MAIL 250
- Supersedes 251
- Copyright 251
- 1996 AllenBradley Company 251
- , Inc. Printed in USA 251
Produits connexes et manuels pour Équipement Rockwell-automation 1770, D17706.5.16 Ref Mnl DF1 Protocol Command
Équipement Rockwell-automation 1752-L24BBBE SmartGuard 600 Controllers User Manua Manuel d'utilisateur
(290 pages)
(290 pages)
Équipement Rockwell-automation 1771-SDN/B INSTL.INSTR.DEVICENET SEMINAR Manuel d'utilisateur
(25 pages)
(25 pages)
Équipement Rockwell-automation Logix5000 Controllers Add-on Instructions Programm Manuel d'utilisateur
(104 pages)
(104 pages)
Équipement Rockwell-automation 1762-OB8 Solid State 24V dc Source Output Module Manuel d'utilisateur
(16 pages)
(16 pages)
Équipement Rockwell-automation 1785-CHBM ControlNet PLC-5 Hot Backup System User Manuel d'utilisateur
(140 pages)
(140 pages)
(5 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels