Rockwell-automation Liqui-Flo Control Configuration Software Version 6 Manuel d'utilisateur télécharger pdf (Page 4)

100

Control and Configuration Software V6.1

Chapter 5 Tuning GV3000 and Liqui-Flo Vector Drives

5.1 Saving the Drive Configuration Before Tuning.................................................5-2

5.2 Using Standard Tuning ....................................................................................5-2

5.3 Using Custom Tuning.......................................................................................5-5

5.3.1 Setting Motor Data ................................................................................5-5

5.3.2 Tuning the Torque/Flux Loop ................................................................5-6

5.3.3 Tuning the Speed Loop .........................................................................5-7

5.3.4 Using Profile To Check Drive Tuning.....................................................5-9

Chapter 6 Monitoring and Editing Drive Parameters

6.1 About the Parameter Monitor...........................................................................6-1

6.2 Adding Parameters to the Monitor List.............................................................6-3

6.3 Removing Parameters from the Monitor List....................................................6-3

6.4 Assigning Values to Parameters on the Drive..................................................6-4

6.5 Saving a Monitor List........................................................................................6-6

6.6 Displaying a Monitor List..................................................................................6-7

6.7 Clearing the Monitor List Display .....................................................................6-8

6.8 Exiting the CS3000 Parameter Monitor............................................................6-8

Chapter 7 Monitoring Drive Status and Alarms

7.1 Displaying and Clearing the Fault Log and Alarm Log.....................................7-1

7.2 Monitoring Drive Status....................................................................................7-4

7.3 Restoring Default Values to Drive Parameters ................................................7-5

7.4 Saving Drive Parameter Values to Non-Volatile Memory on the Drive............7-5

7.5 Restoring Drive Parameter Values from Non-Volatile Memory in the Drive.....7-6

Chapter 8 Controlling the Drive

8.1 Connecting a Drive...........................................................................................8-1

8.2 Disconnecting a Drive ......................................................................................8-1

8.3 Controlling a Drive............................................................................................8-2

8.4 Selecting the Control Source ...........................................................................8-4

8.5 Selecting the Reference Mode (Auto/Manual) .................................................8-4

8.6 Selecting the Direction of Motor Rotation.........................................................8-4

8.7 Setting the Drive Reference.............................................................................8-4

8.8 Setting the Jog Reference................................................................................8-5

8.9 Starting and Stopping the Drive .......................................................................8-5

8.10 Monitoring Drive Indicators ..............................................................................8-6

Chapter 9 Using PC Scope

9.1 About PC Scope...............................................................................................9-1

9.2 Setting Up a Trace ...........................................................................................9-4

9.2.1 Specifying Signals .................................................................................9-5

9.2.2 Setting Up Data Sampling .....................................................................9-5

9.2.3 Setting Up the Trigger............................................................................9-6

9.3 Acquiring a Trace.............................................................................................9-7

9.4 Working with the Cursors .................................................................................9-8

9.4.1 Moving a Cursor ....................................................................................9-9

9.4.2 Specifying the Cursors To Track Each Other ........................................9-9

9.5 Changing Views ...............................................................................................9-9

9.5.1 Turning Cursors On and Off ..................................................................9-9

9.5.2 Magnifying the Trace Display ..............................................................9-10

9.6 Taking a Trace Snapshot ...............................................................................9-10

9.6.1 Taking a Snapshot...............................................................................9-10

1 2 3 4 5 6 7 8 9 ... 99 100

Commentaires sur ces manuels

Pas de commentaire

Rockwell-automation Liqui-Flo Control Configuration Software Version 6 Manuel d'utilisateur Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Rockwell-automation Liqui-Flo Control Configuration Software Version 6