Rockwell-automation 6012DB PowerFlex Medium Voltage Variable Frequency Manuel d'utilisateur Page 59
- Page / 138
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Rockwell Automation Publication 6000-UM001B-EN-P - October 2014 59
Parameters and Function Codes Chapter 4
P232 Filter Time For Overspeed Fault (Lower Limit) 100 ON 0 32767
P233 Threshold Of Over-Speed Fault At Lower Frequency Limit 20 ON 0 199.99
P234 Threshold Of Over-Speed Fault At Upper Frequency Limit 20 ON 0 199.99
P235 Frequency Deviation Warning Cancellation Threshold 0.99 ON 0 199.99
P236 Frequency Deviation Warning Threshold 6 ON 0 199.99
P237 Frequency Deviation Warning Delay (ms) 8 ON 0 32767
P238 Motor Stall Fault Threshold 10 ON 0 199.99
P239 Motor Stall Fault Delay (ms) 6000 ON 0 32767
P240 Transformer Over Temperature Fault Delay (ms) 5000 ON 0 32767
P241 Transformer Over Temperature Warning Delay (ms) 5000 ON 0 32767
P247 Software Interlock: 1-Disable, 0-Enable 1 ON 0 1
P250 Input Contactor/Circuit Breaker Close Delay (ms) 5000 ON 0 10000
P251 Frequency Command-Low Frequency Region Boundary 0.5 ON 0 100
P252 Motor In Stopping Condition Threshold 1 ON 0 100
P253 Motor Coast Stop Time 10 ON 0 10000
P256 Ground Fault Warning Cancellation Threshold 10 ON 0 199.99
P257 Motor Stall Warning Cancellation Threshold 2.98 ON 0 199.99
P259 Frequency Command Analog Offset 0 ON -100 199.99
P260 Frequency Command Analog Scaling Factor 100 ON 0 199.99
P261 Frequency Command Analog Minimum 0.49 ON 0 199.99
P262 Frequency Command Source Selection: 0-Digital, 1-
Analog
0OFF01
P270 Delayed Lockout Time Of Stop Operation (ms) 2000 ON 0 5000
P271 Flux Delay (ms) 50 ON 0 5000
P300 Digital Output #0 Memory Address 99 ON 0 500
P301 Digital Output #0 Logic: 1-Inverting, 0-Non-Inverting 0 ON 0 1
P302 Digital Output #0 Bit Selection (0...15) 0 ON 0 15
P303 Digital Output #0 Delay (ms) 0 ON 0 32767
P304 Digital Output #1 Memory Address 99 ON 0 500
P305 Digital Output #1 Logic: 1-Inverting, 0-Non-Inverting 0 ON 0 1
P306 Digital Output #1 Bit Selection (0...15) 1 ON 0 15
P307 Digital Output #1 Delay (ms) 0 ON 0 32767
P308 Digital Output #2 Memory Address 99 ON 0 500
P309 Digital Output #2 Logic
1: Inverting
0: Non-Inverting
0ON01
P310 Digital Output #2 Bit Selection (0...15) 2 ON 0 15
P311 Digital Output #2 Delay (ms) 0 ON 0 32767
P312 Digital Output #3 Memory Address 99 ON 0 500
Parameter
Number
Description Default
Value
Modify
Root
Lower
Limit
Upper
Limit
- User Manual 1
- Important User Information 2
- Table of Contents 3
- Chapter 4 4
- Parameters and Function Codes 4
- Chapter 5 4
- Preventative Maintenance and 4
- Component Replacement 4
- Appendix D 6
- Appendix E 6
- Introduction 7
- Who Should Use This Manual 7
- What Is Not in This Manual 7
- Additional Resources 7
- General Precautions 8
- Service and Support 8
- Environmental Conditions 10
- How it Works 10
- Simplified Electrical 12
- Diagrams 12
- Standards Compliance 15
- Drive System Layout 17
- Isolation Transformer 18
- Drive System Layout Chapter 2 21
- Chapter 2 Drive System Layout 22
- Door Position Limit Switch 23
- Voltage Sensing Board 24
- Power Module Cabinet 25
- Power Modules 26
- Control Unit (all modules) 30
- Figure 22 - PLC Location 32
- Setup and Operation 33
- Status Indicators 34
- Main Interface Controls 35
- Set Frequency (Hz) 36
- Drive Operation Controls 37
- View Version Information 38
- Active Alarms Controls 39
- Reset Status 39
- Alarm History 40
- Chapter 3 Setup and Operation 42
- Operation 43
- Manual Bypass Cabinet 44
- Automatic Bypass Cabinet 44
- Choose Local/Remote Operation 45
- Open/Close Bypass Contactors 47
- Settings 48
- 4. Press to accept 49
- User Settings 50
- Change User Parameters 50
- Setup Settings 53
- View/Change P or T Parameters 53
- Restore “P” or “T” Parameters 55
- 0 ON -100 199.99 59
- 0 ON -100 100 60
- T Parameters 63
- Alarm List 64
- Daily Inspection 78
- Regular Maintenance Intervals 78
- Physical Checks (No Medium 79
- Voltage or Control Power) 79
- Final Report 80
- Fan Balance 84
- Inspect Isolation Transformer 86
- Inspect Voltage Sensing Board 87
- Replace Voltage Sensing Board 87
- Replace Power Module 91
- Replace Drawout Power Module 93
- Recessed Lifting Handles 94
- Mounting Rail 94
- Finger Assemblies 94
- Install Drawout Power Modules 95
- Replace Power Module Fuses 97
- Drawout Power Module 98
- Inspect or Replace HECS 99
- M5 x 12 Nut 100
- LV Control Cabinet 101
- Replace AC/DC Power Supplies 102
- G3 Power Supply 103
- Inspect UPS 104
- Replace UPS 105
- Replace UPS Batteries 106
- Inspect PLC 108
- Only remove the board using 110
- Inspect the HMI 111
- Replace the HMI 111
- Replace LV Control Relays 113
- Inspect Coils 116
- Inspect Contacts 116
- Inspect Pilot Lights 116
- Connections 117
- Review Firmware and Hardware 118
- Inspect/Review Spare Parts 118
- Technical Specifications 119
- Catalog Number Explanation 121
- Appendix C 123
- PowerFlex 6000 123
- Maintenance Schedule 123
- Spare Parts 127
- Torque Requirements 129
- Rockwell Automation Support 138
- Documentation Feedback 138
Produits connexes et manuels pour Équipement Rockwell-automation 6012DB PowerFlex Medium Voltage Variable Frequency
Équipement Rockwell-automation AK DBU - Dynamic Braking Unit 600/690 VAC Manuel d'utilisateur
(56 pages)
(56 pages)
Équipement Rockwell-automation 2361 Snubber Assembly Replacement (T-Frame) Manuel d'utilisateur
(6 pages)
(6 pages)
Équipement Rockwell-automation 2100 MCC NEMA Type 12 Sealing Instructions Manuel d'utilisateur
(1 pages)
(1 pages)
Équipement Rockwell-automation 8510 AC Spindle Drive System Programming Manual Manuel d'utilisateur
(47 pages)
(47 pages)
Équipement Rockwell-automation 5370-CBPK Color CVIM BLISTER-PAK Option Manuel d'utilisateur
(84 pages)
(84 pages)
Équipement Rockwell-automation 6181 CPU Upgrade for 6181 Industrial Computers Manuel d'utilisateur
(4 pages)
(4 pages)
Équipement Rockwell-automation 2100 CENTERLINE Bolted Pressure Contact Switch Manuel d'utilisateur
(12 pages)
(12 pages)
Équipement Rockwell-automation 2361 Tachometer Feedback Board Replacement Manuel d'utilisateur
(4 pages)
(4 pages)
Équipement Rockwell-automation 8520 9/Series CNC Integration Maintenance Manual D Manuel d'utilisateur
(898 pages)
(898 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels