Rockwell-automation 6012DB PowerFlex Medium Voltage Variable Frequency Manuel d'utilisateur Page 104
- Page / 138
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
104 Rockwell Automation Publication 6000-UM001B-EN-P - October 2014
Chapter 5 Preventative Maintenance and Component Replacement
Inspect UPS
1. Check there are no obstructions or dirt/debris in the exhaust heat fan.
2. Ensure there are no visible signs of damage.
Check UPS Output Voltage
1. Open the LV Control cabinet door.
2. Turn off the back-up control power circuit breaker (Q5) and the customer-
supplied power supply circuit breaker (Q1).
Figure 42 - Circuit Breaker Location in LV Control Cabinet
3. Press ON on the front of the UPS.
4. Using a voltmeter, check the output voltage of the UPS by checking the
input voltage on the line side of the Q2 circuit breaker (equivalent
electrical point).
The input voltage must be 220V AC.
IMPORTANT
If the drive has not been turned on for more than 3 months, the UPS batteries
must be charged for at least 10 hours. Apply either MV to the drive or
customer-supplied control power.
Q1 Q2
Q3
Q6Q5
Circuit Breakers
PLC
LV Control Relays
- User Manual 1
- Important User Information 2
- Table of Contents 3
- Chapter 4 4
- Parameters and Function Codes 4
- Chapter 5 4
- Preventative Maintenance and 4
- Component Replacement 4
- Appendix D 6
- Appendix E 6
- Introduction 7
- Who Should Use This Manual 7
- What Is Not in This Manual 7
- Additional Resources 7
- General Precautions 8
- Service and Support 8
- Environmental Conditions 10
- How it Works 10
- Simplified Electrical 12
- Diagrams 12
- Standards Compliance 15
- Drive System Layout 17
- Isolation Transformer 18
- Drive System Layout Chapter 2 21
- Chapter 2 Drive System Layout 22
- Door Position Limit Switch 23
- Voltage Sensing Board 24
- Power Module Cabinet 25
- Power Modules 26
- Control Unit (all modules) 30
- Figure 22 - PLC Location 32
- Setup and Operation 33
- Status Indicators 34
- Main Interface Controls 35
- Set Frequency (Hz) 36
- Drive Operation Controls 37
- View Version Information 38
- Active Alarms Controls 39
- Reset Status 39
- Alarm History 40
- Chapter 3 Setup and Operation 42
- Operation 43
- Manual Bypass Cabinet 44
- Automatic Bypass Cabinet 44
- Choose Local/Remote Operation 45
- Open/Close Bypass Contactors 47
- Settings 48
- 4. Press to accept 49
- User Settings 50
- Change User Parameters 50
- Setup Settings 53
- View/Change P or T Parameters 53
- Restore “P” or “T” Parameters 55
- 0 ON -100 199.99 59
- 0 ON -100 100 60
- T Parameters 63
- Alarm List 64
- Daily Inspection 78
- Regular Maintenance Intervals 78
- Physical Checks (No Medium 79
- Voltage or Control Power) 79
- Final Report 80
- Fan Balance 84
- Inspect Isolation Transformer 86
- Inspect Voltage Sensing Board 87
- Replace Voltage Sensing Board 87
- Replace Power Module 91
- Replace Drawout Power Module 93
- Recessed Lifting Handles 94
- Mounting Rail 94
- Finger Assemblies 94
- Install Drawout Power Modules 95
- Replace Power Module Fuses 97
- Drawout Power Module 98
- Inspect or Replace HECS 99
- M5 x 12 Nut 100
- LV Control Cabinet 101
- Replace AC/DC Power Supplies 102
- G3 Power Supply 103
- Inspect UPS 104
- Replace UPS 105
- Replace UPS Batteries 106
- Inspect PLC 108
- Only remove the board using 110
- Inspect the HMI 111
- Replace the HMI 111
- Replace LV Control Relays 113
- Inspect Coils 116
- Inspect Contacts 116
- Inspect Pilot Lights 116
- Connections 117
- Review Firmware and Hardware 118
- Inspect/Review Spare Parts 118
- Technical Specifications 119
- Catalog Number Explanation 121
- Appendix C 123
- PowerFlex 6000 123
- Maintenance Schedule 123
- Spare Parts 127
- Torque Requirements 129
- Rockwell Automation Support 138
- Documentation Feedback 138
Produits connexes et manuels pour Équipement Rockwell-automation 6012DB PowerFlex Medium Voltage Variable Frequency
Équipement Rockwell-automation AK DBU - Dynamic Braking Unit 600/690 VAC Manuel d'utilisateur
(56 pages)
(56 pages)
Équipement Rockwell-automation 2361 Snubber Assembly Replacement (T-Frame) Manuel d'utilisateur
(6 pages)
(6 pages)
Équipement Rockwell-automation 2100 MCC NEMA Type 12 Sealing Instructions Manuel d'utilisateur
(1 pages)
(1 pages)
Équipement Rockwell-automation 8510 AC Spindle Drive System Programming Manual Manuel d'utilisateur
(47 pages)
(47 pages)
Équipement Rockwell-automation 5370-CBPK Color CVIM BLISTER-PAK Option Manuel d'utilisateur
(84 pages)
(84 pages)
Équipement Rockwell-automation 6181 CPU Upgrade for 6181 Industrial Computers Manuel d'utilisateur
(4 pages)
(4 pages)
Équipement Rockwell-automation 2100 CENTERLINE Bolted Pressure Contact Switch Manuel d'utilisateur
(12 pages)
(12 pages)
Équipement Rockwell-automation 2361 Tachometer Feedback Board Replacement Manuel d'utilisateur
(4 pages)
(4 pages)
Équipement Rockwell-automation 8520 9/Series CNC Integration Maintenance Manual D Manuel d'utilisateur
(898 pages)
(898 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels