Rockwell-automation 20-COMM-M Modbus/TCP Adapter Manuel d'utilisateur Page 20
- Page / 98
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
2-6 Installing the Adapter
20-COMM-M Modbus/TCP Adapter User Manual
Publication 20COMM-UM014C-EN-P
Connecting the Adapter to
the Network
1. Remove power from the drive.
2. Use static control precautions.
3. Connect one end of an Ethernet cable to the network. See Figure 2.4
for
an example of wiring to a Modbus/TCP network.
Figure 2.4 Connecting the Ethernet Cable to the Network
4. Route the other end of the Ethernet cable through the bottom of the
PowerFlex drive (Figure 2.3
) and insert its Ethernet cable plug into the
mating adapter receptacle.
Applying Power
Install the drive cover or close the drive door, and apply power to the drive.
The adapter receives its power from the connected drive. When you apply
power to the adapter for the first time, its topmost “PORT” status indicator
should be steady green or flashing green after an initialization. If it is red,
there is a problem. Refer to Chapter 5
, Troubleshooting.
Start-Up Status Indications
After power has been applied, the status indicators for the drive and
communications adapter can be viewed on the front of the drive
(Figure 2.5
). Possible start-up status indications are shown in Table 2.A.
!
ATTENTION: Risk of injury or death exists. The PowerFlex
drive may contain high voltages that can cause injury or death.
Remove power from the drive, and then verify power has been
discharged before installing or removing the adapter.
Router
(optional)
Switch
Modbus/TCP
Controller
PowerFlex 7-Class Drives
(each with a 20-COMM-M Adapter)
Modbus/TCP
!
ATTENTION: Risk of equipment damage, injury, or death
exists. Unpredictable operation may occur if you fail to verify
that parameter settings are compatible with your application.
Verify that settings are compatible with your application before
applying power to the drive.
- 20-COMM-M Modbus/TCP Adapter 1
- Important User Information 2
- Summary of Changes 3
- Table of Contents 5
- About This Manual 7
- Rockwell Automation 8
- Conventions Used in This 8
- Getting Started 9
- Features 10
- Compatible Products 10
- Required Equipment 11
- Safety Precautions 11
- 1-4 Getting Started 12
- Quick Start 13
- Status Indicators 14
- Installing the Adapter 15
- Setting the Web Pages 16
- Connecting the Adapter to 17
- Applying Power 20
- Commissioning the Adapter 22
- Configuring the Adapter 23
- Using the PowerFlex 7-Class 24
- Using BOOTP 25
- Configuring the Adapter 3-5 27
- Setting the IP Address 28
- Subnet Mask, and Gateway 28
- Setting the Data Rate 30
- Setting the I/O 30
- Configuration 30
- Setting a Communication 31
- Fault Action 31
- Setting the Message I/O 32
- Setting Web Access Control 33
- Resetting the Adapter 34
- Viewing the Adapter Status 34
- Using Parameters 34
- Flash Updating the Adapter 35
- 3-14 Configuring the Adapter 36
- Chapter 4 37
- Unit Identifier (Port Number) 38
- Using the I/O 39
- Par. 82 - [Maximum Speed] 42
- Accessing Device Parameters 45
- Direct Access Method 45
- Indirect Access Method 46
- Using Datalinks 48
- Rules for Using Datalinks 48
- Reading Datalinks 48
- Writing Datalinks 49
- Conversion Example: 50
- Supported Modbus 51
- Registers 51
- Chapter 5 53
- PORT Status Indicator 54
- MOD Status Indicator 54
- NET A Status Indicator 55
- NET B Status Indicator 55
- Viewing Adapter Diagnostic 56
- Viewing and Clearing 58
- Table 5.B Adapter Events 59
- 5-8 Troubleshooting 60
- Chapter 6 61
- Process Display Pop-up 64
- TCP/IP Configuration Web 65
- Configure E-mail 66
- Notification Web Page 66
- DPI Device Information 69
- Kit (20-XCOMM-DC-BASE) 73
- Specifications 75
- Environmental 76
- Regulatory Compliance 76
- Adapter Parameters 77
- B-6 Adapter Parameters 82
- Logic Command/Status Words 83
- Logic Status Word 84
- PowerFlex 700S Drives 85
- Glossary 87
- G-2 Glossary 88
- F Fault Action 89
- G Gateway 89
- H Hardware Address 89
- I I/O Data 90
- L Logic Command/Logic Status 91
- M Modbus/TCP Network 91
- N NVS (Non-Volatile Storage) 91
- R Reference/Feedback 92
- S Status Indicators 92
- Z Zero Data 92
- May, 2010 98
Produits connexes et manuels pour Équipement Rockwell-automation 20-COMM-M Modbus/TCP Adapter
Équipement Rockwell-automation 140EX-JE2_JE3 Molded Case Circuit Breaker Manuel d'utilisateur
(2 pages)
(2 pages)
Équipement Rockwell-automation 56AMXN ControlLogix/AutoMax/Communication/Module Manuel d'utilisateur
(24 pages)
(24 pages)
Équipement Rockwell-automation 57RF RFID ICODE Handheld Interface User Manual Manuel d'utilisateur
(112 pages)
(112 pages)
Équipement Rockwell-automation 140G_MG- General Warning for Trip Units Manuel d'utilisateur
(1 pages)
(1 pages)
Équipement Rockwell-automation 22-HIM-C2S PowerFlex 4-Class Remote Small HIM Manuel d'utilisateur
(4 pages)
(4 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels