Rockwell-automation 20-COMM-M Modbus/TCP Adapter Manuel d'utilisateur Page 13
- Page / 98
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Getting Started 1-5
20-COMM-M Modbus/TCP Adapter User Manual
Publication 20COMM-UM014C-EN-P
Quick Start
This section is provided to help experienced users quickly start using the
adapter. If you are unsure how to complete a step, refer to the referenced
chapter.
Step Action Refer to…
1 Review the safety precautions for the adapter. Throughout This Manual
2 Verify that the PowerFlex drive is properly installed. Drive User Manual
3 Install the adapter.
Verify that the PowerFlex drive is not powered. Then, connect the
adapter to the network using an Ethernet cable and to the drive
using the Internal Interface cable. Use the captive screws to
secure and ground the adapter to the drive.
Note: When installing the adapter in a DPI External Comms Kit,
refer to the 20-XCOMM-DC-BASE Installation Instructions
(publication 20COMM-IN001) supplied with the kit.
PowerFlex 7-Class DPI
Network Communication
Adapter Installation
Instructions (publication
20COMM-IN004) and
Chapter 2
,
Installing the Adapter
4 Apply power to the adapter.
A. The adapter receives power from the drive. Verify that the
adapter is installed correctly and then apply power to the drive.
The status indicators should be green. If they flash red, there is
a problem. Refer to Chapter 5
, Troubleshooting.
B. Configure/verify key drive parameters.
Chapter 2
,
Installing the Adapter
5 Configure the adapter for your application.
Set adapter parameters for the following functions as required by
your application:
• IP address, subnet mask, and gateway address
• Data rate
• I/O configuration
• Fault action
Chapter 3
,
Configuring the Adapter
6 Set up the master device to communicate with the adapter.
Use a network tool to configure the master device on the Modbus/
TCP network.
Instructions for your
network tool
- 20-COMM-M Modbus/TCP Adapter 1
- Important User Information 2
- Summary of Changes 3
- Table of Contents 5
- About This Manual 7
- Rockwell Automation 8
- Conventions Used in This 8
- Getting Started 9
- Features 10
- Compatible Products 10
- Required Equipment 11
- Safety Precautions 11
- 1-4 Getting Started 12
- Quick Start 13
- Status Indicators 14
- Installing the Adapter 15
- Setting the Web Pages 16
- Connecting the Adapter to 17
- Applying Power 20
- Commissioning the Adapter 22
- Configuring the Adapter 23
- Using the PowerFlex 7-Class 24
- Using BOOTP 25
- Configuring the Adapter 3-5 27
- Setting the IP Address 28
- Subnet Mask, and Gateway 28
- Setting the Data Rate 30
- Setting the I/O 30
- Configuration 30
- Setting a Communication 31
- Fault Action 31
- Setting the Message I/O 32
- Setting Web Access Control 33
- Resetting the Adapter 34
- Viewing the Adapter Status 34
- Using Parameters 34
- Flash Updating the Adapter 35
- 3-14 Configuring the Adapter 36
- Chapter 4 37
- Unit Identifier (Port Number) 38
- Using the I/O 39
- Par. 82 - [Maximum Speed] 42
- Accessing Device Parameters 45
- Direct Access Method 45
- Indirect Access Method 46
- Using Datalinks 48
- Rules for Using Datalinks 48
- Reading Datalinks 48
- Writing Datalinks 49
- Conversion Example: 50
- Supported Modbus 51
- Registers 51
- Chapter 5 53
- PORT Status Indicator 54
- MOD Status Indicator 54
- NET A Status Indicator 55
- NET B Status Indicator 55
- Viewing Adapter Diagnostic 56
- Viewing and Clearing 58
- Table 5.B Adapter Events 59
- 5-8 Troubleshooting 60
- Chapter 6 61
- Process Display Pop-up 64
- TCP/IP Configuration Web 65
- Configure E-mail 66
- Notification Web Page 66
- DPI Device Information 69
- Kit (20-XCOMM-DC-BASE) 73
- Specifications 75
- Environmental 76
- Regulatory Compliance 76
- Adapter Parameters 77
- B-6 Adapter Parameters 82
- Logic Command/Status Words 83
- Logic Status Word 84
- PowerFlex 700S Drives 85
- Glossary 87
- G-2 Glossary 88
- F Fault Action 89
- G Gateway 89
- H Hardware Address 89
- I I/O Data 90
- L Logic Command/Logic Status 91
- M Modbus/TCP Network 91
- N NVS (Non-Volatile Storage) 91
- R Reference/Feedback 92
- S Status Indicators 92
- Z Zero Data 92
- May, 2010 98
Produits connexes et manuels pour Équipement Rockwell-automation 20-COMM-M Modbus/TCP Adapter
Équipement Rockwell-automation 140EX-JE2_JE3 Molded Case Circuit Breaker Manuel d'utilisateur
(2 pages)
(2 pages)
Équipement Rockwell-automation 56AMXN ControlLogix/AutoMax/Communication/Module Manuel d'utilisateur
(24 pages)
(24 pages)
Équipement Rockwell-automation 57RF RFID ICODE Handheld Interface User Manual Manuel d'utilisateur
(112 pages)
(112 pages)
Équipement Rockwell-automation 140G_MG- General Warning for Trip Units Manuel d'utilisateur
(1 pages)
(1 pages)
Équipement Rockwell-automation 22-HIM-C2S PowerFlex 4-Class Remote Small HIM Manuel d'utilisateur
(4 pages)
(4 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels