Rockwell-automation 1771-OFE/B Analog Output Module User Manual Manuel d'utilisateur Page 20
- Page / 84
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
2-6
'&"! * "( $
Rack switch 1 determines what output conditions occur during a rack
fault.
Rack Switch 1
S tti
Configuration Jumper Setting
Setting
MIN MID MAX HOLD LAST STATE
%& && %& && %& && %& && %& &&
%& ! ) %& &&
To set the last state configuration jumpers, proceed as follows.
!
ATTENTION: Do not insert modules into or remove
modules from the I/O chassis while system power is
ON. Failure to observe this rule could result in damage
to module circuitry and unexpected machine operation.
1. Locate the jumpers as shown in Figure 2.1.
2. Carefully pull up on the jumpers to remove from the pins.
3. Reposition as necessary to provide the value selected in
Table 2.A.
Setting Voltage Range Configuration Jumpers (1771ĆOFE1 only)
If you ordered the voltage output version, you must set several
configuration jumpers located inside the module on the circuit board.
To do this, follow these steps:
2. Locate the configuration jumpers and set them according to your
output voltage requirements (Figure 2.3).
%& && '&#'& (
"!'$&"! ' #$%
%% "% "$
"!'$&"!
' #$%
5. Position the jumpers as indicated in Figure 2.3.
- 1
- 1
- Important User Information 2
- 3
- SOC-2 Summary of Changes 4
- Manual's Purpose 5
- Audience 5
- Vocabulary 5
- Manual Organization 5
- Related Products 6
- Product Compatibility 6
- Related Publications 6
- 7
- Chapter 4 8
- Chapter 5 8
- Chapter 6 8
- Chapter 7 8
- Specifications 9
- Block Transfer with 9
- MiniĆPLCĆ2 and PLCĆ2/20 9
- Processors 9
- Table of Contents 10
- Overview of the Analog Output 11
- How Analog Modules 13
- Communicate with 13
- Programmable Controllers 13
- Accuracy 13
- Chapter Summary 13
- 15
- Calculating Power 16
- Requirements 16
- Determine Module 17
- Location in the I/O Chassis 17
- Setting Module 17
- Configuration Jumpers 17
- • the module faults 19
- Install the Keying Bands 21
- Install the Module and Field 22
- Wiring Arm 22
- Connect the Wiring 23
- Ground the Chassis and 24
- Interpreting the Indicator 25
- Configuring Your Output 27
- Configuration Word 29
- Default Configuration 30
- Data Format 30
- Scaling Value Polarity 32
- Figure 3.3 33
- Procedure for Configuring 35
- Your Module 35
- 37
- Block Transfer 38
- Programming Ć PLCĆ2 38
- Family Processors Only 38
- PLC-2 Family Example Program 39
- Table 4.A 40
- Data Table Map 40
- Data Table MAP (128Ćword) 40
- Table 4.B 41
- PLCĆ2 Family Data Table Word 41
- Programming Ć PLCĆ3 42
- Figure 4.4 43
- Programming Ć PLCĆ5 44
- Other Programming 46
- Considerations 46
- Timer/Counter 48
- Accumulated Values 48
- System Expansion 49
- Recommendations Ć PLCĆ2 49
- Processors Only 49
- 51
- Calibrating Your Output 53
- Voltage Output Version 54
- (1771ĆOFE1) 54
- Figure 6.1 55
- Figure 6.2 55
- Figure 6.3 56
- Current Output Version 57
- (1771ĆOFE2) 57
- Channel Calibration 58
- Figure 6.5 59
- Figure 6.6 60
- Location of Resistor Pots 60
- Table 6.C 60
- Resistor Pots 60
- (1771ĆOFE3) 61
- Figure 6.7 62
- Diagnostics and 65
- Troubleshooting 65
- Read Block Transfer 66
- Status Words 66
- 69
- Appendix 71
- Rungs 2 and 3 72
- Rung Summary 72
- Setting the Block Length 73
- (Multiple GET Instructions 73
- Data Table Formats 75
- SignedĆmagnitude Binary 76
- Two's Complement Binary 77
- Table of Contents 80
- AllenĆBradley 81
- Publication Problem Report 81
- BUSINESS REPLY MAIL 82
- Support Services 83
- Worldwide representation 84
Produits connexes et manuels pour Équipement Rockwell-automation 1771-OFE/B Analog Output Module User Manual
Équipement Rockwell-automation 1784-KTCX15 INSTL INSTR CONTROLNET COMM. Manuel d'utilisateur
(18 pages)
(18 pages)
Équipement Rockwell-automation 1760-xxxx Pico Controller User Manual Manuel d'utilisateur
(218 pages)
(218 pages)
Équipement Rockwell-automation 1769-SDN Compact I/O DeviceNet Scanner Module User Manuel d'utilisateur
(156 pages)
(156 pages)
Équipement Rockwell-automation 1786-TCAP INSTL INSTR CONTROLNET TAP DUM Manuel d'utilisateur
(8 pages)
(8 pages)
Équipement Rockwell-automation 1756-L72EROMS Armor GuardLogix Controller Manuel d'utilisateur
(24 pages)
(24 pages)
Équipement Rockwell-automation 1746-QV QUICK START OPEN-LOOP VELOCITY Manuel d'utilisateur
(2 pages)
(2 pages)
Équipement Rockwell-automation 1769-IF8 Compact 1769-IF8 Analog Input Module Manuel d'utilisateur
(32 pages)
(32 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels