Rockwell-automation 1771-N SERIES High Resolution Analog Module User M Manuel d'utilisateur Page 58
- Page / 188
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
4–18 Configuring the Module
Publication 1771ĆUM127B-EN-P - December 2002
Bit/Word Description of Output Configuration Words 5 through 10
Word
Decimal Bit
(Octal Bit)
Definition
Word 5
Bits 00Ć15
(00Ć17)
Low scale value for channel 1. Scale values are limited to
+
32767 in binary format; +7999 in BCD format.
Word 6
Bits 00Ć15
(00Ć17)
High scale value for channel 1. Scale values are limited to
+
32767 in binary format; +7999 in BCD format.
Word 7
Bits 00Ć15
(00Ć17)
Low clamp value for channel 1. The channel output will not be
allowed to go below this value (in scaled units) regardless of
the data sent to the module. Clamp values are limited to
+
32767 in binary format; +7999 in BCD format.
Word 8
Bits 00Ć15
(00Ć17)
High clamp value for channel 1. The channel output will not be
allowed to go above this value (in scaled units) regardless of
the data sent to the module. Clamp values are limited to
+
32767 in binary format; +7999 in BCD format.
Word 9
Bits 00Ć11
(00Ć13)
Maximum ramp rate. If this field is not 0, the module will limit
the maximum rate of change for this channel to be a
percentage of the full scale range of the module. Legal values
are from 1 to 200%.
Bit 12 (14) Constant = 0
Word 9
continued
Bits 13Ć14
(15Ć16)
Reset state. This field controls what an output channel will go
to if the I/O reset line is asserted:
00 binary = last state;
01 binary = minimum output; (example: < Ć10V, < 4mA)
10 binary = maximum output; (example: > 10V, > 22mA)
11 binary = user reset value.
Bit 15 (17)
Alarm enable. If set to 1, the module reports high clamp, low
clamp and rate limit. If 0, these warnings are suppressed.
Word 10
Bits 00Ć15
(00Ć17)
Reset value. If the user selects the channel to go to a user
reset value upon I/O reset, the value in scaled units is entered
here. Otherwise, set to 0.
The above six words of output channel-specific information would
be repeated for the next output channel (2), as shown below. The
bit/word descriptions would be the same as above.
Word/Dec. Bit
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
Word/Octal Bit
17 16 15 14 13 12 11 10 07 06 05 04 03 02 01 00
Channel 2 Programming
11 Low Scale Value
12 High Scale Value
13 Low Clamp Value
14 High Clamp Value
15
Alarm
enable
Reset State 0 Maximum Ramp Rate, % of Full Scale per second
16 Reset Value
- User Manual 1
- Important User Information 2
- ATTENTION 3
- Using this Manual 5
- Related Products 6
- Product Compatibility 6
- Related Publications 7
- Using this ManualP–4 8
- Table of Contents 9
- Chapter 4 10
- Configuring the Module 10
- Table of Contents toc-iii 11
- Table of Contentstoc-iv 12
- Table of Contents toc-v 13
- Table of Contentstoc-vi 14
- Overview of the High 15
- Resolution Isolated 15
- Analog Modules 15
- Features of the High 16
- Analog Series Modules 16
- Refer to 17
- Appendix 17
- Installing the Module 19
- Determine Module 20
- Location in the I/O Chassis 20
- Install the Analog Module 20
- Install the Module in the 21
- Chassis and Connect the 21
- Connecting Wiring 23
- • R = return 26
- • I = input 26
- • O = output 26
- • S = shield 26
- Connecting 4ĆWire 27
- Sourcing Input Analog 28
- Making Your Own Cables 29
- Grounding the Field 30
- Interpreting the 31
- Indicator Lights 31
- Chapter Summary 31
- 2–14 Installing the Module 32
- Communicating With Your 33
- Analog Module 33
- PLCĆ2 Programming 34
- PLCĆ3 Program Example 34
- PLCĆ5 and PLCĆ5/250 35
- Program Example 35
- Module Scan Time 36
- Programming Samples 36
- Setting Up the Data 39
- Table File 39
- Default Configurations 42
- Module Level 43
- Programming Features 43
- Real Time Sampling 45
- Output Channel 46
- Clamping 49
- Alarm Enable 50
- Reset State 50
- Input Channel 51
- Alarm Deadband 52
- Thermocouple Type 54
- Configuration Block for a 55
- Block Transfer Write 55
- Module Status and Input Data 61
- Block Transfer Read 62
- Data Format 62
- Data Header 63
- Input Status Data 64
- Output Status Data 66
- Module Calibration 69
- Calibrating Your Module 70
- Manual Calibration 71
- Figure 6.1 73
- Termination Panel 73
- Output Channel Calibration 75
- Troubleshooting 77
- Troubleshooting with 78
- Status Reported by 78
- Specifications 81
- Grounding Guidelines." 82
- Temperature Specifications 83
- SpecificationsA–6 86
- Important: If you require 60 87
- SpecificationsA–8 88
- Word/Dec. Bit 101
- Word/Octal Bit 101
- Transfer Read Configurations 105
- Series Modules 105
- CSA Hazardous Location 183
- Rockwell Automation Support 188
- Documentation Feedback 188
Produits connexes et manuels pour Équipement Rockwell-automation 1771-N SERIES High Resolution Analog Module User M
Équipement Rockwell-automation 1792D-16VT0LP INSTL INSTR ARMORBLOCK INPUT Manuel d'utilisateur
(8 pages)
(8 pages)
Équipement Rockwell-automation 1792D-16BT0LP INSTL INSTR ARMORBLOCK LP2 16 Manuel d'utilisateur
(8 pages)
(8 pages)
Équipement Rockwell-automation 1769-ARM Compact Address Reserve Module Manuel d'utilisateur
(16 pages)
(16 pages)
Équipement Rockwell-automation 1793-OB4E FLEX INTEGRA 4 PROTECTED OUTPUT Manuel d'utilisateur
(8 pages)
(8 pages)
Équipement Rockwell-automation 1785 User Mnl. PLC-5 Prog.Control Flash Manuel d'utilisateur
(10 pages)
(10 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.063 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels