Rockwell-automation 1738-ADNX ArmorPoint I/O DeviceNet Adapters Manuel d'utilisateur Page 13
- Page / 134
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
1 Publication 1738-UM001A-EN-P - February 2005
Chapter
1
Install the ArmorPoint DeviceNet Adapters
This chapter describes how to install and wire your adapter.
Mount the Adapter and
I/O Base
To mount the ArmorPoint adapter on a wall or panel, use the screw
holes provided in the adapter.
A mounting illustration for the ArmorPoint adapter with I/O bases is
shown below.
Install the mounting base as follows:
1. Lay out the required points as shown in the drilling dimension
drawing.
2. Drill the necessary holes for #8 (M4) machine or self-tapping
screws.
3. Mount the adapter and I/O bases using #8 (M4) screws.
4. Ground the system using the ground lug connection in the I/O
base. (The ground lug connection is also a mounting hole.)
See the following sections: Page:
Mount the Adapter and I/O Base 1-1
Set the Node Address 1-2
Wire the DeviceNet Adapters 1-3
Chapter Summary and What’s Next 1-4
43769
4.02 in.
102 mm
1.81 in.
46 mm
Adapter
1.9 in.
47.2 mm
2.0 in.
50 mm
0.87 in.
22 mm
2.0 in.
50 mm
0.87 in.
22 mm
2.0 in.
50 mm
Drilling Dimension Drawing
- ArmorPoint I/O 1
- DeviceNet 1
- Adapters 1
- Important User Information 2
- Purpose of This Manual 3
- Who Should Use 3
- This Manual 3
- What the Manual Contains 4
- Related Terms 5
- Preface 4 6
- Related Products and 7
- Documentation 7
- Preface 6 8
- Table Of Contents 9
- ii 10
- Appendix D 11
- Default Data Maps 11
- iv 12
- Mount the Adapter and 13
- I/O Base 13
- Set the Node Address 14
- Wire the 15
- DeviceNet Adapters 15
- Chapter Summary and 16
- What’s Next 16
- Use the Adapter 18
- 3. Configure the Subnet I/O 19
- IMPORTANT 21
- Understand the DeviceNet 22
- Network and Subnet 22
- Data Collection 23
- Module Power 23
- Adapter Features 24
- Baudrates 25
- Auto Start Mode 25
- Auto Catalog Replace 26
- Backplane Autobaud 28
- Auto Address 29
- Physical List Acquire Status 29
- Cycling Node Status 30
- Poll Connection Produce Size 30
- Cycling I/O Mapping 31
- Automatic Device Replacement 31
- Physical Ordering 32
- Interscan Delay (ISD) 33
- Expected Packet Rate 33
- Communicate Through 34
- Image Table Mapping 36
- Communicate With 39
- I/O Modules 39
- Use Diagnostic Tables 40
- Use Auto Start Mode 43
- Why Use Auto Start Mode? 44
- Byte Boundaries 45
- Word Boundaries 45
- Double Word Boundaries 45
- Fixed Boundaries 45
- Install the I/O Module 46
- Use RSNetWorx 47
- Double click on 48
- Begin Auto Start Mode 49
- Use Custom Configuration 51
- Configuration Overview 53
- Set the Scanner’s Parameters 55
- DeviceNet Scanner’s Scanlist 61
- Set the Adapter’s Parameters 63
- Chapter Summary 66
- Troubleshoot the ArmorPoint 67
- DeviceNet Adapter 67
- Guidelines for Using 69
- Your Adapter 69
- Specifications 71
- A-2 Specifications 72
- Specifications A-3 73
- A-4 Specifications 74
- Quick Start For the 1738-ADNX 75
- Subnet Out 82
- MACID Parameter 83
- Review of the 1738-ADNX 83
- Rules and the 83
- Review of Auto Start Mode 85
- Browse the Subnet 89
- Inputs and Outputs 93
- Navigate Between Networks 98
- Switch Between Networks 100
- 1. Slot Number 102
- 2. Scanlist tab 102
- 1738-ADNX 105
- Appendix 109
- Message size: 1 Byte 112
- Message size: 6 Bytes 117
- Message size: 4 bytes 119
- Message size: 2 Bytes 119
- Message size: 8 Bytes 121
- 1738-232ASC ASCII Module 123
- 1738-485ASC ASCII Module 123
- D-14 Default Data Maps 124
- 2 126
- 3 127
- 4 128
- 5 129
- 6 130
- How Are We Doing? 131
- BUSINESS REPLY MAIL 132
- Rockwell Automation 134
Produits connexes et manuels pour Équipement Rockwell-automation 1738-ADNX ArmorPoint I/O DeviceNet Adapters
Équipement Rockwell-automation 1746-BAS-T SLC 500 Basic Module/ Instructions Manuel d'utilisateur
(28 pages)
(28 pages)
Équipement Rockwell-automation 1756-DH485 ControlLogix DH-485 Communication Modul Manuel d'utilisateur
(110 pages)
(110 pages)
Équipement Rockwell-automation 1771-TCM,D17716.5.108 TEMPERATURE CONTROL MOD Manuel d'utilisateur
(137 pages)
(137 pages)
Équipement Rockwell-automation 1746-QS,D17466.19 SYNCHRONIZED AXES MODULE Manuel d'utilisateur
(51 pages)
(51 pages)
Équipement Rockwell-automation 1761-HHMK64 Hand-Held Programmer Memory Module Manuel d'utilisateur
(2 pages)
(2 pages)
Équipement Rockwell-automation 1785-L20C_L40C, D17856.5.14 ControlNet PLC-5 Progr Manuel d'utilisateur
(107 pages)
(107 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.117 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels