Rockwell Automation 1785 PLC-5 Manuel d'utilisateur Page 99
- Page / 186
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Transferring Discrete and BlockTransfer Data
Chapter 8
8-4
For the supervisory processor, use the adapter’s configured I/O rack
number to receive data or store data for transfer.
Using Rack 3 (Addresses 0:300:37 and I:30I:37)
Rack 3 is the default discrete-transfer file for PLC-5/12, -5/15, and -5/25
processors. Typically, each output instruction in one processor should have
a corresponding input instruction in the other processor. The rack number
determines the addresses you use.
The ladder logic in the supervisory processor uses the rack number
(0-76 octal) of the adapter-mode processor.
Condition the ladder logic in the adapter processor with I30/10. When
set, this bit indicates a communication failure between the adapter and
supervisory processors.
Creating an Adapter Image FilePLC5/12, 5/15, and 5/25 Processors
If you use 1/2-slot addressing in a 16-slot chassis, you need rack 3
addresses for scanning processor-resident local I/O on the adapter-mode
processor. In this case, you can create an adapter image file for
transferring data. Before you create an adapter image file, make sure that
these conditions are true:
the PLC-5 processor is in adapter mode
the adapter-mode processor is in a 1771-A4B I/O chassis
you are using 1/2-slot addressing
you have not inhibited rack 3 by setting the rack inhibit bit 3 in
processor status word 27
To create the adapter image file, create a 16-word integer file. This file
must be 16 words regardless of whether you use 4-word or 8-word
transfers. This file must be a unique integer file, for use only as an adapter
image file. Words 0-7 are used for output; words 8-15 are used for input.
Bits are numbered in decimal 0-15 for each word.
To tell the processor which file is the adapter image file, enter the file
number in word 25 of the processor status file. You enter this file number
on the processor status screen. For more information about the processor
status screen, see the chapter on using status data in the programming
software documentation.
Important: If you are using an adapter image file (instead of the rack 3
image), then you cannot use block transfers between the supervisor and the
adapter-mode processor.
Programming
Discrete
Transfer in Adapter Mode
- Classic 1785 PLC5 1
- Programmable 1
- Controllers 1
- AllenBradley 1
- Important User Information 2
- Summary of Changes 3
- Table of Contents 4
- Table of Contentsii 5
- Table of Contents iii 6
- Table of Contentsiv 7
- of this Manual 8
- Manual Organization 9
- How to Use this Manual 9
- Understanding Your System 11
- Designing 12
- Systems 12
- Preparing 13
- Functional Specification 13
- Figure 1.2 14
- ProgramDevelopment 14
- Introducing 15
- Classic PLC5 15
- Processor Modules 15
- Using the Classic PLC5 18
- Processor as a Remote I/O 18
- Choosing Hardware 20
- Selecting I/O Module Density 21
- Master/Expander I/O Modules 22
- Selecting I/O Adapter 23
- Other Devices on an I/O Link 24
- Selecting 25
- I/O Chassis 25
- Selecting an Operator 25
- Interface 25
- Other Operator Interfaces 27
- Choosing 28
- a Classic PLC5 28
- Processor for Your 28
- Application 28
- Selecting Power Supplies 28
- Chapter 2 29
- Powering 30
- Table 2.K 30
- 1770XY is a 3.6 V 32
- a PLC5 Processor 33
- Backup System 33
- Selecting Link Terminators 34
- Connecting a 34
- Programming Terminal to a 34
- Processor Module 34
- Choosing Cables 34
- Programming Terminal 35
- Placing System Hardware 36
- Chapter 3 37
- Planning Cabling 40
- Laying Out the 41
- Backpanel Spacing 41
- Grounding Configuration 42
- Assigning Addressing Modes 43
- Racks, and Groups 43
- Understanding the Terms 44
- Used in this Chapter 44
- Choosing the 45
- Addressing Mode 45
- Using 1Slot Addressing 48
- Chapter 4 49
- Using 1/2Slot Addressing 50
- Assigning 51
- Remote I/O Racks 52
- Addressing 54
- Choosing Communication 59
- Chapter 5 60
- Figure 5.1 60
- Front Panels 60
- Configuring Communication 61
- Configuring a DH+ Link 61
- Figure 5.2 62
- Passing 62
- Test Setup 65
- Application Guidelines 66
- Connecting a DH+ Link 68
- Choosing Programming 68
- Terminal Connection 68
- Remote Connection 69
- Serial Connections 70
- 1770KF2/B 71
- Planning Your System Programs 72
- Deciding How to Use an SFC 73
- Preparing the Programs 74
- Organizing a Machine Example 75
- Addressing Data T 78
- is the default file number 79
- the Processor 80
- Status File 80
- Chapter 6 81
- Table 6.F 81
- Status File Addresses 81
- Selecting Interrupt Routines 83
- Program Execution States 84
- Writing a Fault Routine 85
- Major Fault Codes 86
- Chapter 7 87
- Table 7.H 87
- Fault Codes 87
- Programming a Fault Routine 88
- Figure 7.4 89
- Testing a Fault Routine 90
- Setting Up a Fault Routine 90
- Enabling a Fault Routine 90
- Figure 7.5 91
- Setting PowerUp Protection 92
- Understanding 93
- ProcessorDetected 93
- Major Faults 93
- Fault in a Remote I/O Chassis 94
- Rack Fault 94
- Objectives 96
- Transferring Data Using 96
- Adapter Mode 96
- Discrete 99
- Chapter 8 101
- Table 8.K 101
- Programming Block 102
- Transfer in Adapter Mode 102
- Addressing Tips 103
- Figure 8.6 106
- Figure 8.7 107
- Figure 8.8 108
- Figure 8.9 109
- Transferring Data 111
- Using Scanner Mode 111
- Programming Discrete 111
- Transfer in Scanner Mode 111
- BlockTransfer Sequence 114
- Programming 116
- Considerations 116
- Calculating Program Timing 118
- Chapter 9 119
- I/O Scanning 120
- I/O ScanningDiscrete 122
- Figure 9.2 123
- Transferring 123
- Instruction Timing and 124
- Memory Requirements 124
- Processors 125
- File Instructions 128
- Program Constants 130
- Direct and Indirect Elements 130
- Maximizing System Performance 133
- Backplane T 134
- Remote I/O Scan T 134
- Number of Rack Entries 135
- Block Transfers 135
- Calculating 136
- Processor 138
- Calculating Throughput 138
- Selecting Switch Settings 139
- Chassis Backplane with 140
- Adapter Module 140
- Chassis Configuration Plug 141
- Remote I/O Adapter Module 142
- 1771ASB Series C without 142
- Complementary I/O 142
- Appendix A 143
- 1771ASB Series C with 144
- AdapterMode 146
- ProcessorsSW2 146
- PLC5 or Scanner Module 146
- PLC2/20, 2/30, or Sub I/O 147
- Scanner Module System 147
- PLC3 or PLC5/250 System 148
- Design Worksheets 151
- Appendix B 152
- Determine Control Strategy 154
- Identify Chassis Locations 156
- Total I/O Module Requirements 159
- Assign Addresses 160
- Select Adapter Modules 162
- Place System Hardware 164
- Configure Switch Settings 165
- Select Power Supplies 173
- Choose a Programming Terminal 174
- Select Operator Interface 176
- With major offices worldwide 186
Produits connexes et manuels pour Matériel d'enregistrement Rockwell Automation 1785 PLC-5
(63 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.526 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels