Rockwell-automation RECOMM-DNET DeviceNet Adapter for use with DPI AC Manuel d'utilisateur Page 35
- Page / 168
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Configuring the DeviceNet Adapter
4-11
Step 3. If desired, select an additional source of the data to output
to the network in Peer B Output (40). See figure 4.13.
Step 4. Set Peer Out Time (42) and Peer Out Skip (43) to establish
the minimum and maximum intervals between Peer
messages. The minimum interval is set in Peer Out Time
(42). The maximum interval is the value of Peer Out Time
(42) multiplied by the value of Peer Out Skip (43). See
figure 4.14.
Step 5. Set Peer Out Enable (41) to On. The adapter will transmit
the data selected in Peer A Output (39) and Peer B Output
(40) to the network. Another adapter must be configured to
receive the data.
Figure 4.12 – Peer A Output Screen on an LCD OIM
Figure 4.13 – Peer B Output Screen on an LCD OIM
Figure 4.14 – Min Peer TX Time and Peer Out Skip Screens on an LCD OIM
Port 5 Device
RECOMM-DNET
Parameter #: 39
Peer A Output
1
Cmd/Ref
Value Description
0 Off (Default)
1 Logic Command/Reference
2-5 Datalink A, B, C, or D
Input
6-9 Datalink A, B, C, or D
Output
Port 5 Device
RECOMM-DNET
Parameter #: 40
Peer B Output
2
DL A Input
Value Description
0 Off (Default)
1 Logic Command/Reference
2-5 Datalink A, B, C, or D
Input
6-9 Datalink A, B, C, or D
Output
Port 5 Device
RECOMM-DNET
Parameter #: 42
Peer Out Time
10.00 Secs.
0 <> 10.00
Port 5 Device
RECOMM-DNET
Parameter #: 43
Peer Out Skip
1
1 <>16
- DeviceNet Adapter 1
- DPI AC Drives 1
- Contents 3
- List of Figures 7
- List of Tables 9
- Introduction 11
- 1.2 Related Documentation 12
- Electric 13
- Getting Started 15
- 2.2 Required Equipment 16
- 2.3 Installation Checklist 17
- Step Action Refer to 18
- Installing the 19
- 3.5 Applying Power 23
- Configuring the 25
- SP600 Standard 31
- 4.5 Setting the Data Rate 32
- Peer-to-Peer 33
- 4.9 Setting a Fault Action 41
- 4.10 Resetting the Adapter 43
- 00010xxx 45
- 01234567 45
- 1=Enabled 45
- 0=Disabled 45
- Configuring the Scanner 47
- AC Drive 48
- Edit I/O 49
- Parameters 49
- 5.4) appears 49
- 5.3.1 Mapping the Input I/O 52
- 5.3.2 Mapping the Output I/O 53
- 5.4 Saving the Configuration 54
- Using I/O Messaging 55
- 6.4 Using Reference/Feedback 58
- 6.5 Using Datalinks 58
- Using Explicit 67
- Messaging 67
- ControlLogix Controller 68
- Using Explicit Messaging 69
- PLC or SLC Controller 70
- Word Description 71
- 7.4 Running Explicit Messages 73
- 7.5 ControlLogix Example 74
- 7.6 PLC-5 Example 76
- Ladder Logic Program 77
- 7.7 SLC Example 78
- Troubleshooting the 81
- and Network 81
- 8.1.1 DRIVE Status Indicator 82
- 8.1.2 MS Status Indicator 83
- 8.1.3 NET A Status Indicator 84
- 8.2 Adapter Diagnostic Items 85
- Technical 91
- Specifications 91
- 1DPI Port 94
- 2 DPI Data Rate 94
- 3 DN Addr Cfg 94
- 4 DN Addr Actual 94
- 5 DN Rate Cfg 95
- 6 DN Rate Actual 95
- 7 Ref/Fdbk Size 95
- 8 Datalink Size 95
- 9 Reset Module 96
- 10 Comm Flt Action 96
- 11 Idle Flt Action 97
- 12 DN Active Cfg 97
- 13 DPI I/O Config 98
- 14 DPI I/O Active 98
- 15 Flt Cfg Logic 99
- 16 Flt Cfg Ref 99
- Figure B.3 – M-S Input (25) 100
- 26 M-S Output 101
- 27 COS Status Mask 101
- 28 COS Fdbk Change 101
- 29 COS/Cyc Interval 102
- Peer A Input 102
- Peer B Input 102
- 32 Peer Cmd Mask 103
- 33 Peer Ref Adjust 103
- 34 Peer Flt Action 104
- 35 Peer Node to Inp 104
- 36 Peer Inp Timeout 105
- 37 Peer Inp Enable 105
- 38 Peer Inp Status 105
- 43 Peer Out Skip 107
- DeviceNet 109
- C.1 Identity Object 110
- Services 111
- C.2 Connection Object 112
- C.3 Register Object 114
- Instance Attributes 115
- C.4 Parameter Object 116
- C.5 Parameter Group Object 119
- C.6 PCCC Object 121
- C.7 DPI Device Object 123
- C.8 DPI Parameter Object 127
- DeviceNet Objects 129
- Descriptor Attributes 130
- Decimal Places 131
- Decimal Place) 131
- C.9 DPI Fault Object 137
- C.10 DPI Alarm Object 140
- C.11 DPI Time Object 142
- Logic Command/ 145
- Status Words 145
- Logic Status Word 146
- Logic Command/Status Words 147
- Master-Slave 149
- I/O Configuration 149
- Datalinks 152
- Datalinks (Continued) 153
- Datalinks (Continued) 155
- Datalinks 156
- Glossary-1 157
- Glossary-2 158
- Glossary-3 159
- Glossary-4 160
- Glossary-5 161
- Glossary-6 162
Produits connexes et manuels pour Équipement Rockwell-automation RECOMM-DNET DeviceNet Adapter for use with DPI AC
Équipement Rockwell-automation RECOMM-485 RS485 DFI Communications Module Manuel d'utilisateur
(68 pages)
(68 pages)
Équipement Rockwell-automation T8292 Trusted Power Distribution Unit MCB 24V Manuel d'utilisateur
(2 pages)
(2 pages)
Équipement Rockwell-automation 1440-SPD02-01RB XM-220 Dual Speed Module Manuel d'utilisateur
(12 pages)
(12 pages)
Équipement Rockwell-automation MD60 Door-Mount NEMA 1 OIM Bezel Kit MDI Manuel d'utilisateur
(6 pages)
(6 pages)
Équipement Rockwell-automation SP200 AC Drive, 1 2 Channel Analog, Preset Speed Manuel d'utilisateur
(68 pages)
(68 pages)
Équipement Rockwell-automation 440N Magnetically Operated Safety Switch Manuel d'utilisateur
(4 pages)
(4 pages)
Équipement Rockwell-automation T8017 Trusted Peer to Peer Communications Manuel d'utilisateur
(46 pages)
(46 pages)
Équipement Rockwell-automation GV3000/SE Operator Interface Module (OIM) User Gui Manuel d'utilisateur
(112 pages)
(112 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels