Rockwell-automation Migrating PanelView Enhanced Terminal Applications Manuel d'utilisateur Page 43
- Page / 160
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Publication 2711P-QS001A-EN-P - October 2007 43
Review Unsupported Features and Implement Workarounds for Migration Issues Chapter 6
All Displays Display Names In FactoryTalk View ME software, unsupported
characters in display names are replaced with the
underscore character.
Graphic Alignment The graphics may not line up and appear properly.
Resize graphics as needed.
Remote Alarm Ack Bit Array Data Types Workaround with ladder logic change by using the
ack value to indirectly change a tag in an array.
Alarming Controls Acknowledge To PLC Control
Remote Alarm Control Delay Time When an alarm is acknowledged in the FactoryTalk
View ME application, the Ack control, if assigned, is
set immediately, without waiting for a delay time.
Update the ladder logic to implement a delay timer
in PLC.
PLC Controlled Relay Control The terminal does not have a relay. Use the PLC
controller to turn on device.
PLC Controlled Audio Control The terminal does not have audio. Use the PLC
controller to turn on a horn.
Blinking Alarm Messages
Alarm Relays The terminal does not have a relay. Use the PLC
controller to turn on device.
Remote Alarm Operation Hold Time The PanelBuilder 1400e Remote Alarm Ack Control
Hold Time will be used for all alarm hold times. You
can change the hold time in the Advanced tab of the
Alarm Setup editor in FactoryTalk View ME software.
Alarm Handshaking
Message Handshake Control
Security Runtime Password Changes In the PanelBuilder 1400e software, user passwords
are set up in the configuration mode screens.
FactoryTalk View ME software requires the Change
Password button on a display.
Display Security Settings FactoryTalk View ME software uses a different
method to assign security to graphic displays. You
must reapply security. The software uses a logon
system of security similar to RSView32 software.
Once logged on, the operator does not need to
re-enter the password until manually logged off, or
optionally after an idle time.
Unsupported Objects or Features in FactoryTalk View Machine Edition
For this PanelBuilder 1400e object These features are unsupported
in FactoryTalk View ME software
Additional Information
- Migrating 1
- PanelView 1
- Enhanced Terminal 1
- Applications 1
- Important User Information 2
- Where to Start 3
- We Can Get You From 3
- ...To Here 3
- Table of Contents 5
- Chapter 8 7
- Chapter 9 7
- Measure and Improve Runtime 7
- Application Performance 7
- Appendix A 8
- Audience 10
- Required Software 10
- Migration Services 10
- Conventions 11
- Additional Resources 11
- Preface Preface 12
- Migration Considerations 13
- Select a Terminal Replacement 15
- Selecting a Terminal 16
- Replacement 16
- Reviewing Terminal 17
- Comparisons 17
- Installing a PanelView Plus 18
- Terminal 18
- Migrate Your Application 19
- Import Application 21
- About the Conversion Log 26
- Open the Conversion Log 27
- Review the Conversion Log 28
- Review Object Mapping 33
- Reviewing Object Mapping 35
- Reviewing and Modifying 37
- Expressions 37
- Reviewing Unsupported 41
- Features 41
- 8 (SLC controller) or 10 44
- Reviewing Common 46
- Migration Issues and 46
- Workarounds 46
- Required Files and Utilities 46
- Replacing Scrolling List 47
- Replacing the Cursor List 48
- Retain Last State 52
- Replacing the Multistate 56
- Indicator Object List 56
- FactoryTalk View ME Object 58
- Replacing the Local 60
- Message Object List 60
- FactoryTalk View Object 62
- Replacing the Numeric 64
- Data Display Object List 64
- Replacing the Set Bit 68
- Cursor Point Object 68
- Label Tab 73
- Connections Tab 73
- Provide Visual Feedback 76
- State Tab 77
- Bit Position Data Type 80
- Workaround 80
- PLC Controlled Decimal 81
- Point Workaround 81
- Fixed Position Decimal 82
- Ladder Logic Updates to 86
- Support Visible States 86
- Reviewing Diagnostic Lists 93
- Configure the Runtime 94
- Diagnostic Display 94
- Reviewing Error States for 95
- Graphic Objects 95
- Test Run Graphic Displays 96
- Test Run the Application 98
- Configuring Global Memory 99
- Connections 99
- Configure Global Connections 100
- Configuring Communication 102
- Configure RIO 104
- Configure DH+ Communication 106
- ControlNet Communications 109
- Introduction 111
- Before You Begin 111
- What You Need 111
- Follow These Steps 112
- Create the Runtime 113
- Application 113
- Download the Runtime 114
- IMPORTANT 118
- Run the Application 120
- Performance 121
- Benchmarking 123
- Reviewing Tag Update 123
- Response 123
- Measure Performance of 125
- Display Changes 125
- Reviewing Background 126
- Data Log Model 128
- Optimize Tags for 129
- Communication Protocols 129
- , and initial 130
- Export the HMI Tag Database 131
- Export Alarms to XML File 135
- Run the Tag Converter Wizard 137
- Tag1 MotorSart1 N7:0 140
- Re-import the Alarms XML File 144
- Advanced Object Editing 147
- Editing Multiple Objects 148
- Object Explorer 150
- Display Object 152
- Tag Substitution 154
- Rockwell Automation 160
Produits connexes et manuels pour Équipement Rockwell-automation Migrating PanelView Enhanced Terminal Applications
Équipement Rockwell-automation 57C442 Data Highway Plus Interface Module Manuel d'utilisateur
(62 pages)
(62 pages)
(16 pages)
Équipement Rockwell-automation 9323-S5500D A.I. SERIES MICROLOGIX 1000 AND PLC-50 Manuel d'utilisateur
(547 pages)
(547 pages)
Équipement Rockwell-automation 2727-MREB1 MobileView Terminals E-Stop Bypass Manuel d'utilisateur
(2 pages)
(2 pages)
Équipement Rockwell-automation 2755 Hand-Held Cordless Bar Code Scanners Manuel d'utilisateur
(176 pages)
(176 pages)
Équipement Rockwell-automation 2099-BMxx Kinetix 7000 High Power Servo Drive User Manuel d'utilisateur
(190 pages)
(190 pages)
Équipement Rockwell-automation 2198-Hxxx Kinetix 5500 Servo Drives User Manual Manuel d'utilisateur
(244 pages)
(244 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels