Rockwell-automation 1794-OF8IH FLEX Isolated Input/Output HART Analog Manuel d'utilisateur Page 146
- Page / 164
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Publication 1794-UM065B-EN-E - September 2010
134 Use the 1794-OF8IH Module with the Generic Profile
Configuration
Refer to the following tables for configuration information.
Byte Order
Fault Enable
Channel Bits
0…3 [Adapter Name]:[Slot]:C.Data[0].0
[Adapter Name]:[Slot]:C.Data[0].1
4…7 [Adapter Name]:[Slot]:C.Data[0].8
[Adapter Name]:[Slot]:C.Data[0].9
Byte Order
Group B
Byte Order
Group A
Bit 9Bit 8Bit 1Bit 0Description
0 0 0 0 Little Endian Format (default) — all data entries in true Little
Endian format.
1 0 1 0 Word Swap — word swap only values requiring more than
one word, for example, 32 bit float values.
0 1 0 1 Byte Swap — byte swap all words in data table.
1 1 1 1 Big Endian Format — all data entries in true Big Endian
format.
Channel Bits
0 [Adapter Name]:[Slot]:C.Data[0].2
1 [Adapter Name]:[Slot]:C.Data[0].3
2 [Adapter Name]:[Slot]:C.Data[0].4
3 [Adapter Name]:[Slot]:C.Data[0].5
4 [Adapter Name]:[Slot]:C.Data[0].10
5 [Adapter Name]:[Slot]:C.Data[0].11
6 [Adapter Name]:[Slot]:C.Data[0].12
7 [Adapter Name]:[Slot]:C.Data[0].13
Fault Mode Bit 0
Disabled 0
Enabled 1
- Analog Modules 1
- Important User Information 2
- Summary of Changes 3
- Related Documentation 5
- Table of Contents 7
- 1794-IF8IH and 1794-OF8IH 8
- Table of Contents iii 9
- Table of Contents v 11
- What FLEX I/O Analog 13
- Modules Do 13
- Communicate with 14
- Programmable Controllers 14
- Physical Features of 15
- Your Module 15
- Use Alarms on the Input 15
- Overrange Alarm 16
- Underrange Alarm 16
- Remote Fault Alarm 16
- Local Fault Alarm 17
- Use the HART Capabilities 18
- HART Implementation 18
- Features 19
- Select Your Analog Input 20
- Module Operating Features 20
- Data Format 21
- Select Your Analog Output 22
- Latch Mode 23
- Global Reset 23
- Diagnostic Data error 11 24
- = data out of range 24
- Understand Image Table 25
- Mapping and Bit/Word 25
- Descriptions 25
- ATTENTION 27
- Install the Module 28
- Mount on a Panel or Wall 30
- Description Description 31
- IMPORTANT 32
- Label here 33
- Wire the Terminal Base 34
- Connect Wiring to the FLEX 34
- I/O HART Analog Modules 34
- Terminal Base Unit 35
- Ground the Module 36
- Use Programming Software 37
- About the ControlNet and 38
- EtherNet Adapters 38
- Communication Over the 38
- FLEX I/O Backplane 38
- Scheduled Data Transfer 39
- Unscheduled Data Transfer 39
- Module I/O Mapping 39
- I/O Structure 40
- Fault State Data 40
- Device Actions 40
- Data Transfer Types 43
- Configuration Parameters 44
- Byte Order (2 of 2 bits) 47
- Examples 49
- Fault Mode (8 of 1 bit) 50
- Low Alarm Limit (8 of 16 bit) 54
- Real Time Data (RTD) 57
- Profile, Primary Input 57
- Parameters 57
- Profile, Primary Status 58
- High Alarm (8 of 1 bit each) 60
- Low Alarm (8 of 1 bit each) 60
- Loop Alarm (8 of 1 bit each) 61
- HART Status Fields 63
- Secondary Input Data 64
- Table, Cyclic EDT Input 64
- HART PV Status (8 of 8 bits): 67
- Bit 5 Reserved 68
- Bit 6 Reserved 68
- Bit 7 Reserved 68
- HART PV Status 68
- Interpret the Status 69
- Indicators 69
- Module Configuration for 69
- Little Endian Byte Order 75
- Word Swap BYTE ORDER 75
- Profile, Status Parameters 82
- Fault Alarm (8 of 1 bit each) 83
- Diagnostic Data (1 of 8 bits) 83
- Profile, Output Parameters 85
- Global Reset (1 of 1 bit) 86
- Status Indicators 87
- Configure Module Messaging 89
- HART Configuration Quick 90
- Field Value Definition 100
- HART Failed Reason Code 104
- Chapter Summary 106
- Troubleshoot Your Module 107
- FLEX I/O HART Module Commands 109
- Commands 110
- Universal Commands 110
- Common Practice 110
- Device-specific Commands 111
- Appendix 113
- Overview 113
- Message Structure 113
- Burst Mode (not supported) 114
- Start Character 115
- HART Address 115
- HART Command 115
- Byte Count 116
- Check Byte 116
- Response Code 116
- Communication 127
- HART Frame Enhancements 130
- Background Information 131
- Configuration 132
- HART Disable 133
- Channel Data Format 133
- Channel Data Formats 134
- Digital Filters 135
- High Alarm Limit 138
- Low Alarm Limit 138
- Remote High High Alarm Limit 138
- Input Map 139
- High Alarm 140
- Low Alarm 140
- Out of Range 141
- Second Alarm 141
- Diagnostic Status 141
- HART Fault 142
- HART Current Fault 142
- HART Transmitter Present 143
- Local Fault Mode 147
- Digital Mode 152
- Digital Fault Mode 153
- Analog Fault Value 153
- HART Command 3 Disable 153
- Digital Data 154
- Fault Reset 154
- Analog Data 154
- 152 Index 160
- How Are We Doing? 161
- BUSINESS REPLY MAIL 162
- Rockwell Automation 164
Produits connexes et manuels pour Équipement Rockwell-automation 1794-OF8IH FLEX Isolated Input/Output HART Analog
(4 pages)
Équipement Rockwell-automation 2707-M232P3_M485P3 DTAM Micro Operator Interface M Manuel d'utilisateur
(124 pages)
(124 pages)
Équipement Rockwell-automation 57C329 Remote I/O Communications, AutoMax Manuel d'utilisateur
(144 pages)
(144 pages)
Équipement Rockwell-automation 6189x Integrated Display Industrial Computers User Manuel d'utilisateur
(124 pages)
(124 pages)
Équipement Rockwell-automation 2097-Rx Shunt Resistor Installation Instructions Manuel d'utilisateur
(8 pages)
(8 pages)
Équipement Rockwell-automation 9528-APPOWSENE Virtual Image Templates User Manual Manuel d'utilisateur
(120 pages)
(120 pages)
Équipement Rockwell-automation 2090 Ultra3000 Servo Drives Integration Manual Manuel d'utilisateur
(180 pages)
(180 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels