Rockwell-automation 1734-ADNX POINT I/O DeviceNet Adpater User Manual Manuel d'utilisateur Page 48
- Page / 136
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Publication 1734-UM002C-EN-P - July 2003
3-4 Using Auto Start Mode
Are There Any Requirements to Using Auto Start Mode?
There are two requirements to using the Auto Start Mode:
• Your 1734-ADN DeviceNet adapter must use firmware revision
2.001 or higher. If your adapter does not have the required
firmware, you can upgrade it with the ControlFlash tool. For
more information on how to upgrade your adapter’s firmware,
contact your Rockwell Automation representative.
• Your 1734-ADN(X) DeviceNet adapter must be free of I/O
connections on DeviceNet when you use Auto Start Mode. If
another scanner device has established I/O connections with the
adapter, the attempt to use Auto Start Mode is rejected. When
the adapter is configuring itself in Auto Start Mode, no other
device can establish I/O connections to the adapter.
Installing the Adapter
To install the adapter on the DIN rail prior to installing other base
units, proceed as follows.
1. Position the adapter vertically in front of the DIN rail.
2. Press firmly to install the adapter on the DIN rail. The locking
mechanism locks the adapter to the DIN rail.
31110-MC
1734-ADN communication interface
DIN rail
Orange screw slot
- POINT I/O 1
- DeviceNet Adapter 1
- Important User Information 2
- Summary of Changes 3
- Using Change Bars 3
- New and Revised 3
- Information 3
- Summary of Changes 2 4
- Purpose of this Manual 5
- Who Should Use 5
- What the Manual Contains 6
- Related Terms 7
- Preface 4 8
- Related Products and 9
- Documentation 9
- Conventions Used In 10
- This Manual 10
- Table of Contents 11
- Table of Contents ii 12
- Table of Contents iii 13
- Table of Contents iv 14
- Installing the Adapter 16
- Network Node 17
- Address Thumbwheel 17
- Safety end cap 17
- Installing a Replacement 18
- DeviceNet Adapter in an 18
- Existing System 18
- Wiring the Adapter 19
- Chapter Summary and 20
- What’s Next 20
- Using the Adapter 22
- Set Subnet/Backplane Baudrate 23
- Configure the Subnet I/O 24
- Understanding the 26
- DeviceNet Network 26
- Data Collection 27
- Module Power 27
- Adapter Features 28
- Connections 29
- Baudrates 29
- Auto Start Mode 29
- Auto Catalog Replace 30
- Backplane Autobaud 32
- Auto Address 33
- Physical List Acquire Status 33
- Cycling Node Status 34
- Poll Connection Produce Size 34
- Cycling I/O Mapping 35
- Automatic Device Replacement 35
- Physical Ordering 36
- Interscan Delay (ISD) 37
- Expected Packet Rate 37
- Communicating Through 38
- Communicating with 42
- I/O Modules 42
- Using Diagnostic Tables 43
- Using Auto Start Mode 45
- Why Use Auto Start Mode? 46
- I/O Data? 47
- 31111-MC 49
- Installing the I/O Modules 52
- Adding Non-Backplane 53
- Modules to Subnet 53
- (1734-ADNX Only) 53
- Using RSNetWorx 54
- Beginning Auto Start Mode 55
- Using Custom Configuration 57
- Configuring the 1734-ADN(X) 59
- Adapter’s SubNet 59
- Scanner’s Scanlist 67
- • go online with your adapter 69
- Use the Status Indicators 73
- Guidelines for Using 76
- Your Adapter 76
- Specifications 77
- A-2 Specifications 78
- Specifications A-3 79
- A-4 Specifications 80
- 1734-ADNX Quick Start 81
- 20475w-res 88
- Review of the 1734-ADNX 89
- Rules and the MAC ID 89
- Parameter 89
- Review of Auto Start Mode 91
- Browse the Subnet 95
- • All five are there 96
- Inputs and Outputs 98
- Earlier view of 100
- Navigate Between Networks 103
- Switch Between Networks 105
- Slot Number 107
- Scanlist tab 107
- Parameters 108
- How to Use the 1734-ADNX 113
- Default Data Maps 115
- Message size: 1 Byte 116
- Where: 0 = Off 1 = On 119
- Message size: 6 Bytes 120
- Channel Status 121
- Message size: 4 bytes 122
- Message size: 2 Bytes 122
- Message size: 8 Bytes 125
- 1734-232ASC ASCII Module 127
- D-14 Default Data Maps 128
- 2 Index 130
- Index 3 131
- 4 Index 132
- How Are We Doing? 133
- BUSINESS REPLY MAIL 134
- Rockwell Automation 136
Produits connexes et manuels pour Équipement Rockwell-automation 1734-ADNX POINT I/O DeviceNet Adpater User Manual
Équipement Rockwell-automation 1794-L34 FlexLogix Controller System User Manual Manuel d'utilisateur
(130 pages)
(130 pages)
Équipement Rockwell-automation 1784-PCM5/B CABLE Installation Instructions Manuel d'utilisateur
(8 pages)
(8 pages)
Équipement Rockwell-automation 1771-IR Series D RTD Input Module User Manual Manuel d'utilisateur
(79 pages)
(79 pages)
Équipement Rockwell-automation 1792D-KPLT ArmorBlock MaXum Cable Base Manuel d'utilisateur
(16 pages)
(16 pages)
Équipement Rockwell-automation 1757-SWKIT4000 ProcessLogix R400.0 Installation an Manuel d'utilisateur
(293 pages)
(293 pages)
Équipement Rockwell-automation 1771-IBD INSTL INSTR DC (10-30V) INPUT Manuel d'utilisateur
(8 pages)
(8 pages)
Équipement Rockwell-automation 1771-ID16GM Installation Instructions Manuel d'utilisateur
(12 pages)
(12 pages)
Équipement Rockwell-automation 1769-IM12 Compact 1769-IM12 240Vdc Input Module Manuel d'utilisateur
(16 pages)
(16 pages)
Équipement Rockwell-automation 1784-PCM2/B CABLE Installation Instructions Manuel d'utilisateur
(8 pages)
(8 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels