Rockwell-automation 900 Temperature Controller Communications Function Manuel d'utilisateur télécharger pdf (Page 47)

Publication 900-UM004D-EN-E - July 2010

Communications Data 3-5

Table 3.3 Variable Type C3 (83)

Variable

Typ e

Address Item (Parameter) Set (Monitor) Value Function

Group

C3 (83) 0000 Input Type (TC/Pt

multi-input models)

➊

H’00000000 (0): Pt (−200…850°C/−300…1500°F)

H’00000001 (1): Pt (−199.9…500.0°C/−199.9…900.0°F)

H’00000002 (2): Pt (0.0…100.0°C/0.0…210.0°F)

H’00000003 (3): JPt (−199.9…500.0°C/−199.9…900.0°F)

H’00000004 (4): JPt (0.0…100.0°C/0.0…210.0°F)

H’00000005 (5): K (−200…1300°C/−300…2300°F)

H’00000006 (6): K (−20.0…500.0°C/0.0…900.0°F)

H’00000007 (7): J (−100…850°C/−100…1500°F)

H’00000008 (8): J (−20.0…400.0°C/0.0…750.0°F)

H’00000009 (9): T (−200…400°C/−300…700°F)

H’0000000A (10): T (−199.9…400.0°C/−199.9…700.0°F)

H’0000000B (11): E (0…600°C/0…1100°F)

H’0000000C (12): L (−100…850°C/−100…1500°F)

H’0000000D (13): U (−200…400°C/−300…700°F)

H’0000000E (14): U (−199.9…400.0°C/−199.9…700.0°F)

H’0000000F (15): N (−200…1300°C/

−300…2300°F)

H’00000010 (16): R (0…1700°C/0…3000°F)

H’00000011 (17): S (0…1700°C/0…3000°F)

H’00000012 (18): B (100…1800°C/300…3200°F)

H’00000013 (19): Infrared temperature sensor (K 140°F/60°C)

H’00000014 (20):Infrared temperature sensor (K 240°F/120°C)

H’00000015 (21):Infrared temperature sensor (K 280°F/140°C)

H’00000016 (22): Infrared temperature sensor (K 440°F/220°C)

H’00000017 (23): 0…50 mV

H’00000018 (24): W (0... 2300°C/0...3200°F)

H’00000019 (25): PL II (0... 1300°C/0...2300°F)

Initial

setting

Input Type (analog

input models) ➊

H’00000000 (0): 4…20 mA

H’00000001 (1): 0…20 mA

H’00000002 (2): 1…5 V

H’00000003 (3): 0…5 V

H’00000004 (4): 0…10 V

C3 (83) 0001 Scaling Upper Limit Scaling lower limit +1…0000270F (scaling lower limit +1…9999)

C3 (83) 0002 Scaling Lower Limit H’FFFFF831 to Scaling upper limit -1 (-1999 to scaling upper limit

-1)

C3 (83) 0003 Decimal Point

Position (TC/Pt

multi-input models)

H’00000000…H’00000001 (0…1)

Decimal Point

Position (analog input

models)

H’00000000…H’00000003 (0…3)

C3 (83) 0004 Temperature Unit H’00000000(0): °C

H’00000001(1): °F

C3 (83) 0005 SP Upper Limit The range of values (without decimal point) is as follows:

Temperature: SP lower limit + 1 to Input range upper limit

Analog: SP lower limit + 1 to Scaling upper limit

C3 (83) 0006 SP Lower Limit The range of values (without decimal point) is as follows:

Temperature: Input range lower limit to SP upper limit - 1

Analog: Scaling lower limit to SP upper limit - 1

C3 (83) 0007 PID/ ON/OFF H’00000000(0) ON/OFF

H’00000001(1) 2-PID Control

C3 (83) 0008 Standard/Heating

and Cooling

H’00000000(0): Standard

H’00000001 (1) Heating and cooling

➊ The input type can be selected to march the connected sensor. There are two input types specifications:

Thermocouple/Resistance thermometer input and Analog input.

➋ The parameter will not be shown on the Controller display when alarm 3 is not assigned to an output.

➌ Communications parameters are enabled after they have been changed by resetting the controller.

➍ For controllers with two event inputs (events 1 and 2), this cannot be set if the number of Multi-SP uses parameter is set to 1

or 2

➎ For controllers with two event inputs (events 1 and 2), this cannot be set if the number of Multi-SP uses parameter is set to 2.

➏ PRST (program start) can be set even when the program pattern is set to OFF, but the function will be disabled.

➐ The logic of CompoWay/F (900-TC) operation command code 00 (communications writing) is not affected.

➑ The setting (monitor) range depends on the transfer output type setting. (See the setting data list for details.)

➒ P.END (program end output) can be set even when the program pattern is set to OFF, but the

function will be disabled.

➓ The output turns ON when the status of either the Control Output 1 ON/OFF Count Alarm or the Control Output 2 ON/OFF

Count Alarm turns ON.

1 2 ... 42 43 44 45 46 47 48 49 50 51 52 ... 102 103

Commentaires sur ces manuels

Pas de commentaire

Rockwell-automation 900 Temperature Controller Communications Function Manuel d'utilisateur Page 47

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Rockwell-automation 900 Temperature Controller Communications Function