Rockwell-automation 1794-APBDPV1 FLEX I/O PROFIBUS Adapter User Manual Manuel d'utilisateur Page 71
- Page / 153
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Publication 1794-UM064B-EN-P - May 2014
Communicate With Your Module 59
1794-ID2 – Incremental Encoder Module Image Table Mapping
1794-ID2 Pulse Counter Module Word/Bit Definitions for Block Transfer Read Words
Word Bit Definition
Read Word 0 Bit 00 Ch 0 Input A – (pulse transmitter 0) – This bit, when set, indicates a signal at A.
Bit 01 Ch 0 Input B – (pulse transmitter 0) – This bit, when set, indicates a signal at B.
Bit 02 Ch 0 Input Z – (pulse transmitter 0) – This bit, when set, indicates a signal at Z.
Bit 03 Ch 0 Input G – (pulse transmitter 0) – This bit, when set, indicates a signal at G.
Bit 04 Ch 1 Input A – (pulse transmitter 1) – This bit, when set, indicates a signal at A.
Bit 05 Ch 1 Input B – (pulse transmitter 1) – This bit, when set, indicates a signal at B.
Bit 06 Ch 1 Input Z – (pulse transmitter 1) – This bit, when set, indicates a signal at Z.
Bit 07 Ch 1 Input G – (pulse transmitter 1) – This bit, when set, indicates a signal at G.
Bit 08 (10) Calibrated 0 – This bit, when set (1), indicates that the counter 0 has been calibrated. This bit
is reset by CalReset.
Bit 09 (11) Calibrated 1 – This bit, when set (1), indicates that the counter 1 has been calibrated. This bit
is reset by CalReset.
Bit 10 (12) Ch 0 Counter Stored – This bit, when set (1), indicates a counter value is saved in store 0. This
bit is reset by StoreReset.
1151
- User Manual 1
- Important User Information 2
- Summary of Changes 3
- Chapter 1 4
- Table of Contents 5
- Table of Contents vii 7
- Who Should Use this 9
- Purpose of this Manual 9
- Related Documentation 10
- Common Techniques Used 11
- APBDPV1 Module 13
- Purpose of the FLEX I/O 14
- PROFIBUS 14
- APBDPV1 Adapter 14
- Differences Between APB 14
- PROFIBUS APBDPV1 15
- Adapter Components 15
- Mount and Remove 16
- Your System 16
- Optional Accessories 17
- Mounting Kit (1794-NM1) 18
- Mounting Dimensions and 19
- Spacing Requirements 19
- Communicate With Your Module 21
- Polled I/O Structure 22
- Input Status Word Bits 23
- I/O Module Fault 23
- Map Data into the Image 24
- FT for all 27
- Channels 27
- Chx SS Config 35
- 1794-IE4XOE2 Memory Map 37
- 1794-IR8 Memory Map 40
- 1794-IT8 Read and Write Words 44
- 1794-IT8 Word/Bit Description 46
- Setting the Input Filter 56
- Configure Your Input Channels 66
- Setting the Input Filters 67
- calibration 70
- Read Word 9 76
- 3210765411 10 9 815 14 13 12 79
- 32 10765411 10 9 815 79
- 14 13 12 79
- Defaults 80
- The DP Physical Layer 83
- Cabling and Equipment 84
- Required for Line A Type 84
- Required for Line B Type 85
- Connect the Adapter to the 86
- D-Shell Pin Assignment 87
- Terminate the Network 88
- Communication 91
- Enter User Parameter Data 92
- Auto Configure Format 93
- Condensed Format 93
- User Parameter Example 95
- Full Format 96
- Enter Check Configuration 98
- Adapter Status Word 99
- Chapter Summary 101
- PROFIBUS Module 103
- View status from the 104
- Master’s Configuration 104
- Software 104
- Apply FLEX I/O Modules 107
- Classification 108
- Define the Area 108
- Select Protection 109
- Method(s) 109
- Match Field Devices 109
- Module source voltage=17V 110
- Module sense 110
- Specifications 113
- Environmental Specifications 114
- Certifications 114
- 104 Specifications 116
- Device Data Base (GSD) File 117
- EndModule 118
- Teaching GSD Entry 119
- Non-EDT Module Teaching Entry 120
- I/O Profile: 121
- EDT Modules Teaching Entry 124
- Teach an I/O Module to 127
- Work with 1794-APBDPV1 127
- Appendix 134
- Overview 134
- Message Structure 134
- Burst Mode (not supported) 135
- Start Character 136
- HART Address 136
- HART Command 136
- Byte Count 137
- Check Byte 137
- Response Code 137
- HART Field Device Error Codes 138
- Universal Commands 139
- Common Practice Commands 140
- Numerics 148
- 2 Index 149
- Index 3 150
- 4 Index 151
- Rockwell Automation Support 153
- Documentation Feedback 153
Produits connexes et manuels pour Équipement Rockwell-automation 1794-APBDPV1 FLEX I/O PROFIBUS Adapter User Manual
Équipement Rockwell-automation 6181X-15xxxxxxx VersaView 6181X-IN001B-MU-P Manuel d'utilisateur
(104 pages)
(104 pages)
Équipement Rockwell-automation 57C620 AutoMax Programming Executive Version 3.8 Manuel d'utilisateur
(298 pages)
(298 pages)
Équipement Rockwell-automation 1798-IE4 FlexArmor Analog Input Module Manuel d'utilisateur
(8 pages)
(8 pages)
Équipement Rockwell-automation 57C411 Module Specs Resolver Input Module Manuel d'utilisateur
(2 pages)
(2 pages)
Équipement Rockwell-automation 8520-OM Offline Development System User Manual Manuel d'utilisateur
(100 pages)
(100 pages)
Équipement Rockwell-automation 6159 Industrial 17 inch CRT Monitors, Series B Manuel d'utilisateur
(36 pages)
(36 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels