Rockwell-automation 1747-DTAM-E,D17476.1 Data Table Access Module (DTA Manuel d'utilisateur Page 55
- Page / 116
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Publication 1747-6.1
Chapter
7
Processor Control Functions
This chapter describes the procedures to:
• change processor modes
• view and clear processor faults
• transfer user programs between RAM and EEPROM memory
Changing the
Processor to Run
Mode
The module must be configured for the Modify mode to change the
processor to Run mode. If the module is attached to a 5/03 processor,
the keyswitch must also be in the REM position to change the
processor mode.
When the module is attached to a processor, the module displays the
Ready Attached screen with the processor operating mode displayed
in the upper right-hand corner:
1. To place the attached processor into the Run mode from any
screen where data is not being entered:
Press
2. The module displays:
3. To confirm:
Press
4. The processor enters the Run mode and the module displays:
RDY> 4 RHALT
5/02 1111
Confirm?
Enter RUN,
- Data Table 1
- Access Module 1
- Allen-Bradley 1
- Important User Information 2
- Summary of Changes 3
- S-2 Summary of Changes 4
- Table of Contents 5
- Table of Contents v 7
- Who Should Use this 9
- Purpose of this Manual 9
- Contents of this Manual 10
- Related Documentation 11
- Common Techniques 11
- Used in this Manual 11
- Allen-Bradley Support 12
- Local Product Support 12
- Technical Product Assistance 12
- Data Table Access Module 13
- Overview 13
- Installation and Power Up 15
- 2-2 Installation and Power Up 16
- Installation and Power Up 2-3 17
- Connecting Your 18
- Equipment 18
- Installation and Power Up 2-5 19
- Module Configuration 20
- Installation and Power Up 2-7 21
- Access Port View 21
- Power-Up Sequence 22
- Module Setup Procedure 23
- Factory Default 24
- Settings 24
- Entering the Setup 25
- Selecting the 26
- Language 26
- Selecting the Node 26
- Setting the Baud Rate 27
- Setting the Auto 27
- Attach Function 27
- Backlighting the LCD 28
- Setting the Monitor 28
- Override Function 28
- Accepting Module 29
- Setup Parameters 29
- Using the Module 29
- 3-8 Module Setup Procedure 30
- AttachingtoaProcessor 31
- Auto Attach Procedure 32
- Attaching to a Processor 4-3 33
- Attachingtoa 34
- Password Protected 34
- Processor 34
- Monitoring and Modifying Data 35
- Logical Data File 37
- Addressing 37
- Backspace Function 38
- During Data File 38
- Address Entry 38
- Quick Access 39
- .1 40
- Entering Data File 41
- Addresses 41
- Entering Bit Addresses 41
- Entering Integer Addresses 42
- How to Change 43
- Displayed Data File 43
- Elements 44
- How to Change Data 46
- File Values 46
- How to Change Word Values 46
- 0000000000101000 49
- Quick Recall Functions 51
- Using Quick Recall 52
- Functions 52
- Clearing Quick Recall 53
- 6-4 Quick Recall Functions 54
- Processor Control Functions 55
- Changing the 56
- Processor to Program 56
- Viewing Processor 56
- Clearing Processor 57
- Transferring Memory 58
- Message Capability 61
- Programming the MSG 62
- Instruction 62
- 5/02 Control Block 62
- Configuration 62
- Message Capability 8-3 63
- 5/03 Control Block 64
- Message Capability 8-5 65
- 8-Word Message 66
- 16-Word Message 67
- 12-Word Message 68
- 13-Word Message 69
- 18-Word Message 70
- 1-Word Message 71
- Application Example 1 72
- Message Capability 8-13 73
- B3:1.0/1 74
- B3:1.0/3 75
- ENTER LOW RANGE 76
- ENTER HIGH RANGE 76
- NO VALUE ENTERED 77
- Application Example 2 78
- Message Capability 8-19 79
- ENTER NEW VALUE? 80
- Troubleshooting 81
- 9-2 Troubleshooting 82
- Module Problems 83
- Using the LCD 83
- Communication 84
- Problems Using the 84
- Troubleshooting 9-5 85
- 9-6 Troubleshooting 86
- Function Problems 87
- Troubleshooting MSG 88
- Instruction Error 88
- Troubleshooting 9-9 89
- 9-10 Troubleshooting 90
- Processor Faults 91
- 9-12 Troubleshooting 92
- Troubleshooting 9-13 93
- 9-14 Troubleshooting 94
- Specifications 95
- Characteristics 96
- Not accessible from the DTAM 97
- Address Structure 98
- Data File 3 - Bit 101
- Data File 4 - Timers 102
- Data File 5 - Counters 103
- Data File 6 - Control 104
- Data File 7- Integer 105
- Publication 1747-6.1 106
- Module Display Character Set 107
- Mounting Template 109
- D-2 Mounting Template 110
- 111
- I-2 Index 112
- I-4 Index 114
Produits connexes et manuels pour Équipement Rockwell-automation 1747-DTAM-E,D17476.1 Data Table Access Module (DTA
Équipement Rockwell-automation 1763 MicroLogix 1100 Programmable Controllers User Manuel d'utilisateur
(256 pages)
(256 pages)
Équipement Rockwell-automation 1788-FFCT NI-FBUS Configurator User Manual Manuel d'utilisateur
(86 pages)
(86 pages)
Équipement Rockwell-automation 1772-AF3,D17726.5.2 User Manual AUX FUNCT PROM Manuel d'utilisateur
(32 pages)
(32 pages)
Équipement Rockwell-automation 1734-XXXX POINT I/O and ArmorPOINT I/O DeviceLogix Manuel d'utilisateur
(112 pages)
(112 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels