Rockwell-automation FactoryTalk Historian SE 3.0 UniInt Interface User Manuel d'utilisateur Page 19
- Page / 108
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
UniInt Interface User Manual 13
Parameter
Description
/stopstat=digstate
or
/stopstat
/stopstat only is
equivalent to
/stopstat="Intf
Shut"
Optional
Default = no digital state
written at shutdown.
If the /stopstat parameter is present on the startup
command-line, then the digital state Intf Shut will be
written to each Historian Point when the interface is stopped.
If /stopstat=digstate is present on the command-line,
then the digital state, digstate, will be written to each
Historian Point when the interface is stopped. UniInt uses the
first occurrence in the table.
If neither /stopstat nor /stopstat=digstate is
specified on the command-line, then no digital states will be
written when the interface is shut down.
Examples:
/stopstat=shutdown
/stopstat="Intf Shut"
The entire digstate is enclosed within double quotes when
there is a space in digstate.
/uht_id=#
Optional
Default = Health tags are not
filtered by location3 unless
UniInt failover is used
The /uht_id=# command-line parameter is used to specify
a unique ID for interfaces that are run in a redundant mode
without using the UniInt failover mechanism. There are
several Rockwell Automation interfaces that are UniInt based
and implement their own version of failover. In order for health
tag(s) to be configured to monitor a single copy of the
interface, an additional parameter is required. If the
/uht_id=# is specified, only health tags with a location3
value = # will be loaded.
/uiinfops=s
Optional (not recommended)
Default = UI_IF_INFO
The /uiinfops command-line parameter is used in
conjuction with the Interface Informaiton point and is
described in more detail in the Interface Monitoring Points
section. The interface by default looks for a point with the
point source UI_IF_INFO and checks to see if the point is the
Interface Monitoring point. This point source can be changed
but if it is, the /uiinfops will have to be added to every
interface in order for the interfaces to find the Interface
Information point.
/uitrace=x
Optional
Default = no tracing enabled
If the /uitrace command-line parameter is specified, the
values and timestamps that are received by the interface are
also written to the log file. Tracing can be enabled for a
particular point by specifying /uitrace=x, where x is the point
number or tag name of the point to be traced. This parameter
should be used with caution because specifying this
parameter could cause the log file to become very large.
- UNIINT INTERFACE USER MANUAL 1
- Table of Contents 3
- Introduction 7
- Running Modes 10
- Informational Parameters 10
- Standard Parameters 11
- is when the 14
- Interface Startup Parameters 20
- /updateinterval=# 20
- What are Historian Points? 21
- Interface Points 21
- Point Attributes 22
- Input Points 28
- Output Points 29
- I/O Rate Points 31
- Performance Points 32
- Performance Summaries 33
- UniInt and PI SDK 33
- “Known Servers” Table 34
- Interface Operation 35
- Historian Point Updates 36
- Exit Handler 36
- Windows Performance Counters 39
- UniInt Performance Counters 41
- directory 44
- Interface Health Points 45
- Interface Point Count 49
- IO Rate 49
- Message Counter 50
- Output Rate 50
- Output Bad Value Rate 50
- Trigger Input Rate 51
- Trigger Input Bad Value Rate 51
- Scan Class Health Tags 51
- Scan Class Scan Time 54
- Operating Systems 55
- Interface 56
- Buffering 56
- Limitations 58
- Outputs 59
- ICU Configuration 61
- Operation 66
- Creation 67
- Validation 68
- Construction 68
- Utilization 69
- Synchronization 70
- Remote Cache Builds 71
- Messages 72
- Configuration Errors 74
- Troubleshooting 76
- 3. Delete the cache files 77
- Configuring UniInt Failover 81
- Data Source Points 82
- Historian Tags 83
- Historian Tag 84
- Description 84
- Steady State Operation 87
- Glossary 88
- Failover ID 89
- Failover Update Interval 89
- Heartbeat Point 89
- Hot Failover 89
- Input Data 90
- Failover Scenarios 91
- Manual Failover 96
- UniInt Failover Scheme 100
- Maximum Data Overlap 103
- Message Logs 105
- Messages on Windows 105
- System Errors and PI Errors 105
- Definition of, 2 107
Produits connexes et manuels pour Équipement Rockwell-automation FactoryTalk Historian SE 3.0 UniInt Interface User
Équipement Rockwell-automation T8471 Trusted TMR 120V dc Digital Output Module Manuel d'utilisateur
(2 pages)
(2 pages)
Équipement Rockwell-automation MaxPak Plus NRG Meter Filter Kit 23C30 Manuel d'utilisateur
(4 pages)
(4 pages)
Équipement Rockwell-automation T8290 Trusted Output Power Distribution Unit Manuel d'utilisateur
(10 pages)
(10 pages)
Équipement Rockwell-automation SD3100 DISTRIB PWR SYS SD3100 DC PWR MODULE Manuel d'utilisateur
(76 pages)
(76 pages)
Équipement Rockwell-automation CEP7-ERR CEP7 Remote Reset Accessory Module Manuel d'utilisateur
(8 pages)
(8 pages)
Équipement Rockwell-automation T8110B Trusted Industrial Control System Manuel d'utilisateur
(2 pages)
(2 pages)
Équipement Rockwell-automation CA6-TC420 Sprecher+Schuh CA6 Terminal Cover Kit Manuel d'utilisateur
(4 pages)
(4 pages)
Équipement Rockwell-automation Micro 100 DC Drive Heatsink Kit, 1DN2000 Manuel d'utilisateur
(4 pages)
(4 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels