Rockwell-automation 193-EC4 EC4 Current Monitoring Relay User Manual Manuel d'utilisateur Page 108
- Page / 157
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Rockwell Automation Publication 193-UM011A-EN-P - September 2010 109
Using DeviceLogix™ Chapter 10
8. Place the cursor on the left of the Bit Output block and press the left
mouse button. Draw a line from the Bit Output block to the Out of the
BOR function block and double-click the left mouse button to establish a
connection.
9. Repeat steps 3 through 8 to add a second BOR function block that
monitors Input 3 and 4 to control Output B of the EC4.
10. Disable Edit mode by de-selecting the Edit mode button or through
the Tools menu.
- EC4 Current Monitoring Relay 1
- Important User Information 2
- IMPORTANT 3
- DNET-UM072_-EN-P 4
- Table of Contents 5
- Product Overview 10
- Diagnostic Parameters 12
- Trip Relay 12
- Inputs and Outputs 12
- Status Indication 13
- Test/Reset Button 13
- Node Address Switches 14
- DeviceNet Compatibility 14
- Flash Memory 14
- Installation and Wiring 15
- Starter Installation 16
- Starter Assembly Instructions 17
- 193-EC_ _E) 18
- Cat. No. 193-EC_ _B) 20
- Cat. No. 193-EC_ _E) 21
- Power Terminals 22
- Terminal Designations 23
- Grounding 24
- Short-Circuit Ratings 24
- Fuse Coordination 25
- Typical Motor Connections 25
- Single-Phase Full-Voltage 26
- External Line Current 27
- Transformer Application 27
- Installation Instructions 28
- External Ground Fault 29
- Sensor Application 29
- E3 Plus Overload Relay 30
- Cat. No. 193-CBCT_ 30
- Ground Fault Sensor 30
- Cat. No. 193-CBCT1 31
- Typical Control Circuit 32
- Wiring Diagrams 32
- Single-Phase 33
- Three-Phase 33
- Warning Enable 35
- Overcurrent Protection 35
- Introduction 35
- Trip Enable 35
- Overcurrent Warning 36
- Overcurrent Trip 36
- Ground Fault Protection 37
- Ground Fault Setting Range 38
- Ground Fault Trip 38
- Ground Fault Trip Inhibit 39
- Ground Fault Warning 39
- Undercurrent Protection 40
- Undercurrent Trip 41
- Communication Fault 42
- Protection 42
- Communication Idle 43
- Comm Idle Warning 44
- Remote Trip 44
- Preventive Maintenance 45
- Diagnostics 45
- Queue Clearing 46
- DeviceNet Node Commissioning 47
- Using RSNetWorx for DeviceNet 48
- Figure 26 - EDS Wizard Screen 50
- Programmable Parameters 57
- Monitor Params (All 58
- Read-Only) 58
- Advanced Setup Group 60
- For Catalog Number 193-EC4ZZ 66
- Reset/Lock Group 71
- DeviceNet Setup Group 72
- Output Setup Group 75
- DeviceLogix Group 79
- Current Monitoring Parameters 81
- Reporting Accuracy 82
- Ground Fault Current 83
- Reporting 83
- Monitor Group 83
- Trip History and Snapshot 90
- Trip History Codes 92
- Warning History Codes 93
- Trip Snapshot 94
- Explicit Messaging 96
- (0x0375) 102
- Using DeviceLogix™ 104
- DeviceLogix Programming 105
- Troubleshooting 110
- Network Status LED 111
- OUT A & OUT B LEDs 111
- DeviceNet Modes of 112
- Operation 112
- Power-Up Sequence 112
- Run Mode 113
- Recoverable Error Mode 113
- Unrecoverable Error Mode 113
- Resetting a Trip 114
- Trip/Warn LED 114
- Procedures 114
- DeviceNet Troubleshooting 115
- Input and Output 115
- ➊ FRN 2.000 and later 116
- Specifications 117
- Table 4 - Input Ratings 118
- Environmental 119
- Table 9 - Protection 120
- DeviceNet Information 122
- Identity Object – Class 123
- Code 0x01 123
- Message Router – Class 124
- Code 0x02 124
- DeviceNet Object – Class 124
- Code 0x03 124
- Assembly Object – Class 125
- Code 0x04 125
- Input Assemblies 126
- Connection Object – Class 128
- Code 0x05 128
- Discrete Input Point Object 132
- – Class Code 0x08 132
- Discrete Output Point 132
- Object – Class Code 0x09 132
- Parameter Object – Class 133
- Code 0x0F 133
- Parameter Group Object – 135
- Class Code 0x10 135
- Control Supervisor Object – 139
- Class Code 0x29 139
- Acknowledge Handler 142
- Object – 0x2B 142
- DeviceNet Interface Object 143
- – Class Code 0xB4 143
- ODVA Fault Codes 144
- Logic Supervisor Object 145
- CLASS CODE 0x030E 145
- Status Object - CLASS 145
- CODE 0x0375 145
- CE Compliance 148
- Low Voltage Directive 149
- Two-Speed Applications 150
- Accessories 151
- Rockwell Automation Support 157
- Documentation Feedback 157
Produits connexes et manuels pour Équipement Rockwell-automation 193-EC4 EC4 Current Monitoring Relay User Manual
Équipement Rockwell-automation 140G-H-xxxx Stored Energy Operating Mechanism Manuel d'utilisateur
(5 pages)
(5 pages)
(6 pages)
Équipement Rockwell-automation 140 Manual Motor Starter / Circuit Breaker Manuel d'utilisateur
(7 pages)
(7 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels