Rockwell-automation 1769-IF16V Compact High Density Analog Input Modul Manuel d'utilisateur Page 14
- Page / 84
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
14 Publication 1769-UM018A-EN-P - October 2008
Chapter 2 Installation and Wiring
Hazardous Location Considerations
This equipment is suitable for use in Class I, Division 2, Groups A, B,
C, D or non-hazardous locations only. The following attention
statement applies to use in hazardous locations.
Prevent Electrostatic Discharge
ATTENTION
EXPLOSION HAZARD
• Substitution of components may impair suitability for Class I,
Division 2.
• Do not replace components or disconnect equipment unless
power has been switched off or the area is known to be
non-hazardous.
• Do not connect or disconnect components unless power has
been switched off or the area is known to be non-hazardous.
• This product must be installed in an enclosure.
• All wiring must comply with N.E.C. article 501-4(b).
ATTENTION
Electrostatic discharge can damage integrated circuits or
semiconductors if you touch analog I/O module bus connector pins
or the terminal block on the input module. Follow these guidelines
when you handle the module:
• Touch a grounded object to discharge static potential.
• Wear an approved wrist-strap grounding device.
• Do not touch the bus connector or connector pins.
• Do not touch circuit components inside the module.
• Use a static-safe work station, if available.
• When it is not in use, keep the module in its static-shield box.
- 1769-IF16C, 1769-IF16V 1
- Important User Information 2
- Table of Contents 3
- Chapter 4 4
- Module Diagnostics and 4
- Troubleshooting 4
- About this Publication 7
- Who Should Use This 7
- Publication 7
- Additional Resources 8
- Conventions 8
- Overview 9
- Chapter 1 Overview 10
- System Overview 11
- Module Operation 11
- Installation and Wiring 13
- ATTENTION 14
- Remove Power 15
- Reduce Noise 15
- Assemble the Compact I/O 16
- Mounting the Module 17
- Mount to a Panel 18
- Replace a Single Module 19
- Within a System 19
- Grounding the Module 20
- System Wiring Guidelines 21
- Label the Terminals 23
- Remove the Finger-safe 23
- Terminal Block 23
- Wire the Finger-safe 23
- Wire the Modules 25
- Terminal Layout 26
- Configuration 29
- Input Image 30
- Output Image 30
- Configuration File 30
- Input Data File 31
- Time Stamp Value (Word 16) 32
- General Status Bits (S0…S15) 32
- Low Alarm Flag Bits (L0 …L15) 32
- High Alarm Flag Bits (H0…H15) 32
- Output Data File 33
- Configuration Data File 34
- Channel Configuration 38
- Enable/Disable Channel (EC) 39
- Input Filter Selection 39
- Channel Step Response 40
- Input Type/Range Selection 41
- Input Data Selection Formats 41
- Engineering Units 42
- Scaled-for-PID 42
- Percent Range 42
- Real Time Sampling 43
- Time Stamping 43
- Process Alarms 44
- Alarm Deadband 45
- Introduction 47
- Safety Considerations 47
- Power Cycle Diagnostics 48
- Channel Diagnostics 49
- Non-critical vs. Critical 50
- Module Errors 50
- Module Error Definition 50
- Error Codes 51
- Invalid Input Range Selected 55
- Invalid Input Filter Selected 55
- Invalid Input Format Selected 56
- Alarm Not Enabled 56
- Invalid Alarm Data 56
- Module Inhibit Function 57
- Contacting Rockwell 57
- Automation 57
- Specifications 59
- Input Specifications 60
- Certifications 61
- Replacement Parts 61
- I:3.17/2 63
- Module Configuration File 64
- Configure Analog I/O 64
- Modules in a MicroLogix 64
- 1500 System 64
- Appendix 69
- Add the Module to Your 69
- Profile 70
- 5. Click OK 70
- Configure Each I/O Module 72
- Positive Decimal Values 73
- Negative Decimal Values 74
- Glossary 75
- Ideal Transfer 77
- Actual Transfer 77
- Function 77
- Rockwell Automation 84
Produits connexes et manuels pour Équipement Rockwell-automation 1769-IF16V Compact High Density Analog Input Modul
Équipement Rockwell-automation 1787-PLUG10R Installation Instructions Manuel d'utilisateur
(1 pages)
(1 pages)
Équipement Rockwell-automation 1734-XXXX POINT I/O Digital and Analog Modules and Manuel d'utilisateur
(221 pages)
(221 pages)
Équipement Rockwell-automation 1785-Lx0E,D178510.5 QUICK START ETHERNET PLC-9 Manuel d'utilisateur
(29 pages)
(29 pages)
Équipement Rockwell-automation 1788-CN2FFR EtherNet/IP and ControlNet to FOUNDATI Manuel d'utilisateur
(104 pages)
(104 pages)
Équipement Rockwell-automation 1769-OF4 Compact I/O Analog Output Module Manuel d'utilisateur
(24 pages)
(24 pages)
Équipement Rockwell-automation 1788-CNCHKR ControlNet NetChecker User Manual Manuel d'utilisateur
(24 pages)
(24 pages)
Équipement Rockwell-automation 1771-QDC, D17716.5.85(Passport) MNL. PLASTIC MOLDI Manuel d'utilisateur
(197 pages)
(197 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.083 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels