Rockwell-automation 1746-NR4 SLC RTD/Resistance Input Module User Manu Manuel d'utilisateur Page 63
- Page / 148
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
63 Publication 1746-UM008B-EN-P - December 2006
Chapter
5
Channel Configuration, Data, and Status
This chapter examines the channel configuration word and the
channel status word bit by bit. It explains how the module uses
configuration data and generates status during operation. It gives you
information about how to:
• configure a channel.
• examine channel input data.
• check a channel’s status.
Channel Configuration
The channel configuration word is a part of the RTD module’s output
image. Output words 0…3 correspond to channels 0…3 on the
module. Setting the condition of bits 0…15 in these words via your
ladder logic program causes the channel to operate as you choose (for
example, RTD type or reading in °C). Output words 4…7 are used to
further define the channel configuration to let you choose a scaling
format other than the module default when using the proportional
counts data format. You can use words 4 and 5 to define one user-set
range and words 6 and 7 to define a second range.
A bit-by-bit examination of the configuration word is provided in the
Channel Configuration Word (O:e.0 through O:e.3) - Bit Definitions
table on page 66. Programming is discussed in chapter 6. Addressing
is explained in chapter 4.
Module Output Image (Configuration Word)
CH 0 Configuration Word
015
015
015
015
O:e.0
O:e.1
O:e.2
O:e.3
CH 1 Configuration Word
CH 2 Configuration Word
CH 3 Configuration Word
Defines user±set lower scale limit for range 0
015
015
015
015
O:e.4
O:e.5
O:e.6
O:e.7
Defines user±set upper scale limit for range 0
Defines user±set lower scale limit for range 1
Defines user±set upper scale limit for range 1
- SLC 500 1
- RTD/Resistance 1
- Input Module 1
- Important User Information 2
- Summary of Changes 3
- New Information 3
- 4 Summary of Changes 4
- Table of Contents 5
- 6 Table of Contents 6
- Use This Manual 7
- Who Should Use This 7
- Purpose of This Manual 7
- Contents of this Manual 8
- Common Techniques Used 9
- 10 Preface 10
- Overview 11
- 12 Overview 12
- RTD Compatibility 13
- 14 Overview 14
- Overview 15 15
- Hardware Overview 16
- System Overview 18
- System Operation 19
- LED Indicator Status 20
- 22 Overview 22
- Quick Start Guide 23
- Procedures 24
- Insert the Module 25
- Wire the Module 25
- Configure Your I/O 28
- Output Image Detail 29
- 30 Quick Start Guide 30
- Input Image Detail 31
- Monitoring Status 32
- Install and Wire the Module 33
- NR4 Power Requirements 34
- Module Location in Chassis 35
- General Considerations 37
- Module Installation and 38
- Install the Module 39
- Remove the Module 39
- Terminal Wiring 40
- IMPORTANT 41
- Cable Examples 46
- Calibration 47
- Single-point Calibration 48
- Module ID Code 51
- Module Addressing 52
- O : 4 . 2 53
- I : 3 . 6 53
- Channel Filter Frequency 54
- Selection 54
- Effective Resolution 55
- 10 Hz Filter Notch Frequency 56
- 50 Hz Filter Notch Frequency 57
- 60 Hz Filter Notch Frequency 57
- 250 Hz Filter Notch Frequency 57
- Scanning Process and 58
- Channel Timing 58
- Scanning Cycle 60
- Channel Turn-on, Turn-off 61
- Response to Slot Disabling 61
- Input Response 62
- Output Response 62
- Procedure 64
- Enter the Configuration Data 65
- Scaled–for–PID 68
- Temperature Counts 69
- -200 °C (-328 °F) -32,768 69
- +630 °C (1166 °F) +32,767 69
- Scaling Examples 71
- 1746-NR4 73
- Scaling Select (Bits 13-14) 78
- User-set Scaling 79
- Limit Scale Words 80
- Channel Data Word 81
- Channel Status Checking 82
- Bits Define 83
- These bit settings 83
- Indicate this 83
- 1514131211109876543210 83
- Input Type Status (Bits 0…3) 84
- Excitation Current (Bit 12) 85
- Broken Input Error (Bit 13) 85
- Out-of-range Error (Bit 14) 86
- Configuration Error (Bit 15) 86
- Ladder Programming Examples 87
- Initial Programming 88
- Configuration Word Setup 89
- Copy File Data Flow 89
- Programming Procedure 90
- Dynamic Programming 91
- Verify Channel 92
- Configuration Changes 92
- Interface to the PID 93
- Instruction 93
- Use the Proportional 95
- Counts Data Format with 95
- Monitor Channel Status 96
- Invoke Autocalibration 97
- Introduction 99
- Module Operation vs 99
- Channel Operation 99
- Power Turn-on Diagnostics 100
- Channel Diagnostics 100
- LED Indicators 100
- Error Codes 102
- Out-of-range Detection 103
- Troubleshooting Flowchart 105
- Replacement Parts 106
- Contact Rockwell 106
- Automation 106
- Application Examples 107
- Channel Configuration 108
- Program Listing 109
- Program to Convert °F to BCD 110
- Supplementary Example 111
- Degrees Selector Switch 114
- Specifications 117
- 118 Specifications 118
- Module Accuracy 119
- 120 Specifications 120
- Specifications 121 121
- 122 Specifications 122
- RTD Standards 123
- 124 RTD Standards 124
- Configuration Worksheet 125
- I/O Configuration 131
- 132 I/O Configuration 132
- I/O Configuration 133 133
- 6. Click OK 134
- Glossary 135
- 136 Glossary 136
- Glossary 137 137
- 138 Glossary 138
- 140 Index 140
- Index 141 141
- 142 Index 142
- How Are We Doing? 143
- BUSINESS REPLY MAIL 144
- Rockwell Automation 148
Produits connexes et manuels pour Équipement Rockwell-automation 1746-NR4 SLC RTD/Resistance Input Module User Manu
Équipement Rockwell-automation 1756-OF8I ControlLogix Eight-channel Isolated Anal Manuel d'utilisateur
(208 pages)
(208 pages)
Équipement Rockwell-automation 1747-L40 SLC 500 Fixed Hardware Style Manuel d'utilisateur
(223 pages)
(223 pages)
Équipement Rockwell-automation 1766-Lxxxx MicroLogix 1400 Programmable Controller Manuel d'utilisateur
(406 pages)
(406 pages)
Équipement Rockwell-automation 1769-IT6 Compact I/O 1769-IT6 Thermocouple/mV Inpu Manuel d'utilisateur
(168 pages)
(168 pages)
Équipement Rockwell-automation 1792-IB8XOB8PLP INSTL INSTR ARMORBLOCK LP 8/8 Manuel d'utilisateur
(12 pages)
(12 pages)
Équipement Rockwell-automation 1792-IB4/B INSTL.INST ARMORBLOCK 4 INPUT Manuel d'utilisateur
(36 pages)
(36 pages)
Équipement Rockwell-automation 1747-PBASE BASIC Development Software Programming Manuel d'utilisateur
(144 pages)
(144 pages)
(1 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels