Rockwell-automation 1440-TBS-J XM Dynamic Measurement Module Terminal Manuel d'utilisateur

Installation InstructionsXM Dynamic Measurement Module Terminal BaseCatalog Number 1440-TBS-JTopic PageImportant User Information 2Environment and Enc

10 XM Dynamic Measurement Module Terminal Base Publication ICM-IN003D-EN-P - March 2013DIN Rail Grounding Block24V Common GroundingThe XM system is

XM Dynamic Measurement Module Terminal Base 11Publication ICM-IN003D-EN-P - March 2013 Terminating ResistorsThe XM Bus operates correctly when the

12 XM Dynamic Measurement Module Terminal Base Publication ICM-IN003D-EN-P - March 2013Install the Terminal BaseThe terminal base can be DIN rail o

XM Dynamic Measurement Module Terminal Base 13Publication ICM-IN003D-EN-P - March 20132. Slide the terminal base unit over leaving room for the si

14 XM Dynamic Measurement Module Terminal Base Publication ICM-IN003D-EN-P - March 2013Interconnect Terminal Base UnitsFollow the steps below to in

XM Dynamic Measurement Module Terminal Base 15Publication ICM-IN003D-EN-P - March 2013Panel/Wall MountingInstallation on a wall or panel consists

16 XM Dynamic Measurement Module Terminal Base Publication ICM-IN003D-EN-P - March 20135. Position the terminal base unit up tight against the neig

XM Dynamic Measurement Module Terminal Base 17Publication ICM-IN003D-EN-P - March 2013No. Desc. No. Desc. No Desc.Channel 00 Xdcr 0 (+)Channel 116

18 XM Dynamic Measurement Module Terminal Base Publication ICM-IN003D-EN-P - March 2013Specifications(1)Use this Conductor Category information for

XM Dynamic Measurement Module Terminal Base 19Publication ICM-IN003D-EN-P - March 2013Non-operating temperatureIEC 60068-2-1 (Test Ab, Unpackaged

2 XM Dynamic Measurement Module Terminal Base Publication ICM-IN003D-EN-P - March 2013Important User InformationSolid state equipment has operation

20 XM Dynamic Measurement Module Terminal Base Publication ICM-IN003D-EN-P - March 2013Surge Transient ImmunityIEC 61000-4-5:±1 kV line-line (DM) a

XM Dynamic Measurement Module Terminal Base 21Publication ICM-IN003D-EN-P - March 2013(1)See the Product Certification link at http://www.ab.com f

22 XM Dynamic Measurement Module Terminal Base Publication ICM-IN003D-EN-P - March 2013Additional ResourcesThese documents contain additional infor

XM Dynamic Measurement Module Terminal Base 23Publication ICM-IN003D-EN-P - March 2013Notes:

Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400Rockwell Automation SupportRockwel

XM Dynamic Measurement Module Terminal Base 3Publication ICM-IN003D-EN-P - March 2013Environment and EnclosureATTENTIONThis equipment is intended

4 XM Dynamic Measurement Module Terminal Base Publication ICM-IN003D-EN-P - March 2013North American Hazardous Location ApprovalThe following infor

XM Dynamic Measurement Module Terminal Base 5Publication ICM-IN003D-EN-P - March 2013European Hazardous Location ApprovalThe following applies whe

6 XM Dynamic Measurement Module Terminal Base Publication ICM-IN003D-EN-P - March 2013Prevent Electrostatic DischargeAbout the Terminal BaseWARNING

XM Dynamic Measurement Module Terminal Base 7Publication ICM-IN003D-EN-P - March 2013The 1440-TBS-J uses spring-clamp termination. Component Ident

8 XM Dynamic Measurement Module Terminal Base Publication ICM-IN003D-EN-P - March 2013Before You BeginTo effectively use the terminal base, note th

XM Dynamic Measurement Module Terminal Base 9Publication ICM-IN003D-EN-P - March 2013Wiring RequirementsUse solid or stranded wire. All XM wiring